We are building a cinder block fence for a private house: stages of work, recommendations, photos

The foundation base of a country house is the basis and support for load-bearing walls. Its main purpose is to protect the inside of the building from water leakage and cold air penetration. Carefully selected bricks for the foundation plinth eliminate problems in subsequent operation.

Basement brick should not only be beautiful: strength and moisture resistance are equally important characteristics Source it.decorexpro.com

DIY fencing installation

Required tools:

• cord;
• roulette;
• chalk;
• pegs;
• sledgehammer, hammer, crowbar;
• shovel;
• welding machine;
• grinder with cutting disc for concrete;
• trowel;
• concrete mixer;
• level;
• brush.

A fence made of concrete blocks is similar to brickwork, only the blocks have larger overall dimensions.

Hollow blocks are often chosen for fencing construction, as they are lighter and cheaper than solid ones, and at the same time just as strong. In addition, masonry can be easily reinforced through voids.

Preparatory work

Using pegs and a cord, the territory is marked. Pegs are driven in and a cord is pulled between them to mark the axis of the fence. The boundaries of the trench for the strip foundation are marked with chalk.

The trench is dug using a shovel. The width of the trench is twice the width of the block fencing masonry plus 0.4 meters. Depth, if the soil is not heaving - 0.7 meters. If the soils are wet, then the foundation is buried 0.2 meters deeper than the soil freezing mark. Data about the level of soil freezing in a particular region is found in building codes and regulations.

Strip foundation device

The durability of the structure depends on the careful manufacturing of the foundation and the quality of its components. So, you need to do the following:

1. The bottom of the trench is compacted, then drainage layers of sand and crushed stone (0.1 meters each) are made, each layer is successively watered and compacted. The walls and bottom of the trench are covered with roofing felt to provide waterproofing and prevent soil from spilling onto the foundation.
2. Concrete solution is being prepared. Components: cement M200, crushed stone, sand in a ratio of 1-5-3 and water. It is convenient to make the concrete mixture using a concrete mixer.
3. 0.1 meter of concrete mortar is poured onto the drainage with waterproofing, and after it hardens, formwork from boards is installed. The formwork is provided with spacers so that under the pressure of concrete (or earth on the other side) it retains the required shape.
4. To ensure the strength of the structure, a frame made of reinforcement is placed in the formwork, fastened with knitting wire or welding. The frame is made of reinforcement with a diameter of 12 mm or more. Four longitudinal rods are connected by vertical and transverse rods in increments of 10 to 20 cm. The frame should be made smaller in size than the formwork by 2-5 cm on each side.
5. Vertical outlets from reinforcement are attached to the frame with the expectation that they will enter the masonry of blocks through the voids in them for a better connection between the foundation and the fence. The height of the outlets above the foundation is 15 cm. Pipe racks for future pillars are also attached to the frames, strictly vertical in level at the marking points.
6. We install the first rack at the beginning of the frame. The location of the second rack is determined experimentally. Next to the trench, parallel to it, blocks are laid out, first for the post, then for the fence, taking into account the mortar joints, about 3-4 meters in total. The middle of the next pillar block will show the axis of the second pillar. This is necessary so that a whole number of blocks fit in the span. Having studied the markings, you can then perform it using a tape measure.
7. Pour the concrete solution into the formwork. The mixture is compacted well using a crowbar so that there are no sinuses. The formwork is removed after a week, when the concrete gains strength.
8. The vertical surfaces of the foundation are coated with bitumen mastic and the previously laid roofing material is glued to it. The free space between the foundation and the trench is covered with earth and compacted.

Laying a fence made of concrete blocks

The construction of the fence begins with the construction of pillars from special concrete blocks in places where pipes or reinforcement have already been removed from the foundation to the height of the pillar. If the blocks are without grooves, then after 3-4 rows between them horizontal reinforcing masonry meshes are placed, releasing them from the pillars (so that these meshes will later fit into the masonry of the fence).

Cement mortar for masonry is made from cement and sand in a ratio of 1-4 with the addition of water.

Wall concrete blocks are laid on the foundation in rows, observing the bandaging of the seams, as in brickwork. The distance between two vertical joints of adjacent rows must be at least one third of the length of the block.

The verticality and horizontality of each laid block is checked with a building level. Blocks of one row are placed along the construction thread.

The blocks are laid with rustic jointing. It is recommended to make the thickness of the mortar joint 1-1.5 cm. To fasten the fence to the foundation, the voids of the first row of masonry blocks are filled with concrete mortar. When the fence laying is completed, the post is covered with a special post cover, and the fence canvas is covered with a gable cover.

Laying methods

Laying walls made of cinder block material is possible in several ways.

1) In two stone blocks.

2) One and a half blocks.

3) In one cinder block.

4) Half a stone.

The solution must be laid no more than one and a half centimeters thick. If the layer is thicker, the thermal insulation properties of the finished structure may decrease. To increase these properties, it is better to leave the voids inside the blocks unfilled. The solution is placed only at the joints of the blocks and where it is needed. When the wall is ready, the voids in it are filled with very fine slag, which is then carefully compacted.

In any case, the construction process is much faster than if you used ordinary bricks. This is due to the size of the material and the ease of its use. So, the brick is smaller in size, so you will need twice as much of it. Consequently, more movements will have to be performed. And a lot of cement will also be used. This means that cinder block saves money. When the process of constructing the walls is completed, you need to begin their hydro- and thermal insulation. This is necessary to prevent moisture from reaching the surface of the material.

This is especially important to do before you install the roof.

Once the walls are completely weatherproofed, the roof frame is installed. It is constructed after all work related to the building frame is completed. To prevent condensation from forming between the ceiling and the roof of the house and moisture from collecting, vapor and waterproofing materials should be laid between them. When the roof installation is completely completed, it is necessary to perform a vapor barrier on the ceiling. It, like the entire roof, must be insulated inside with basalt or mineral wool.

Useful tips

If you decide to build a house from cinder blocks, then you first need to build the strongest and highest possible foundation. Experts recommend turning to tape options.

We must not forget that cinder block walls are very dense. Because of this, many craftsmen are faced with the problem of laying pipes and electrical wiring. As a rule, specialists in such cases turn to special equipment. That is why it is advisable to think about carrying out this work in advance if you are going to do it yourself.

When choosing this building material, always pay special attention to its filler. The best options are those with shell rock, expanded clay, sawdust and crushed stone.

They are safe and environmentally friendly.

Be sure to ensure the integrity of the cinder blocks when selecting them.

In addition, you should pay attention to the identity of the geometry of several elements located in different pallets

When it comes to transporting cinder blocks, pallets are most often used here. However, you can also resort to simple storage. Blocks can only be stored on pallets. They should be located under a canopy to protect them from the harmful effects of various atmospheric precipitations. Hollow elements should be placed with the voids facing down.

Experts say that it is quite possible to check the quality of a cinder block using an ordinary 15 mm nail - try sticking it into the material below with your own hands. If a nail goes into it, this will indicate that the quality of the blocks is not the highest.

Please note that cinder blocks that were produced without the use of a special vibrating machine are much inferior in strength characteristics to elements that were produced using a similar technique. They can only be used in the construction of simple non-residential premises.

Cinder blocks cannot boast of high thermal insulation characteristics, such as, for example, foam blocks

Therefore, if you are building a residential building from these materials yourself, then you will have to pay special attention to the thickness of the seams. If they turn out to be too thick, the building will turn out cold - heat will simply escape through the seams to the outside

An excessively thick layer of mortar (more than 1.5 cm) will negatively affect the thermal insulation qualities of the walls.

If you decide to finish cinder blocks with a plaster mixture, then first you need to prepare them for this work. Otherwise, the plaster simply will not stick to the blocks.

Before proceeding with the construction of this or that building from cinder blocks, you need to correctly calculate their required quantity. To do this, you need to calculate how many parts there will be in 1 m3. For example, a material with parameters 390x190x188 mm can be calculated in this way: 39x19x18.8 = 13930; 1000000 (cube volume): 13930=71. There will be 71 blocks in 1 m3.

Don't skimp on purchasing cinder blocks. Too cheap materials may turn out to be of low quality or even dangerous from an environmental point of view.

The pros and cons of cinder blocks are discussed in the following video.

Insulation

If you do not insulate the base of the foundation, then in the cold season, up to a third of its heat can escape from the house. Heating costs increase, housing comfort decreases, dampness and mold appear.

Using extruded polystyrene foam to insulate the foundation base is one of the best options. It is attached with construction adhesive and fixed with a special fastener. When installed correctly, the surface is perfectly flat.

First you need to mark everything and calculate the required amount of insulation. Then adjust the individual sheets to size. Install a metal profile below the level to support the first row of insulation.

Apply glue to the sheets and attach them to the base carefully so that the adhesive mixture does not protrude beyond the edges. Then secure the sheets with fastening dowels, slightly recessing the caps into the insulation.

It is also necessary to provide protection for the insulation from the sun. The plaster mesh is attached with the same glue, another layer is applied so that the thickness is 4-5 millimeters. After the glue has dried, the base is lined with a pre-selected material.

Masonry technology

After the reinforcement mesh is installed on the foundation of the structure, you need to begin the laying process. You will have to lay out the base frame from the corners. In this case, after the first row is completed, the evenness of the structure is checked using a building level. Brick laying on the foundation is carried out in strictly horizontal rows of one brick or 1.5, less often 2 bricks. Each stage of masonry is covered with mortar, the thickness of which is approximately 2.5 cm. After the brick foundation becomes four rows high, it is recommended to begin the process of building walls. The base surface is finished mainly with decorative stone. It happens that tiles are used as a finishing material for a building.

The base must be placed on waterproofing.

If you plan to build a basement floor on a brick foundation, you should take care of installing a ventilation system. It is better to place ventilation holes at a height of 15 cm from ground level. The size of the window depends on the overall diameter of the vent pipes. The base should not be laid on the ground, using a waterproofing layer in the upper part. Therefore, upon completion of the installation of insulation, layers of roofing material are laid.

If insulation of the structure is planned in the future, the layout is done in one and a half bricks.

Properties that a brick for a plinth should have

Considering all of the above, it is clear that the brick for building a basement must have the following properties:

• increased compressive strength (from 200 MPa);
• standard dimensions - 250x120x65 mm;
• high environmental friendliness;
• moisture resistance;
• relief surface.

The strength of the brick ensures the reliability and durability of the base and the entire structure as a whole. Standard sizes will ensure a smooth and attractive appearance of the base and the entire building in particular.

The beauty of the base speaks about the thoroughness and thoroughness of the work done Source kirpichmaster.ru

In addition, the construction of the basement will be less labor-intensive. The absence of harmful impurities in the brick will prevent harm to the residents of the house. The embossed surface of the brick adheres remarkably well to the mortar and prevents the formation of cracks and cracks and, accordingly, cold bridges.

Roof of a house made of expanded clay concrete

Your home should be comfortable and cozy, so you should choose your roof wisely. The simplest option is a gable roof made of corrugated board. This material is the most popular because it is inexpensive and durable, does not require continuous formwork, and due to its light weight there is also no need for reinforced rafters.

1. A mauerlat is attached to the last row of the wall - a wooden board connecting the rafters and the wall.

The rafter system is assembled on the ground. First, the outer rafter legs are raised and installed, a control thread is stretched between them, along which all other rafters will be aligned.

The waterproofing is spread and fixed with a counter-lattice along the rafters. The sheathing is stuffed and corrugated sheets are laid.

The video shows the process of constructing a roof in a very accessible and clear way:

A house made of expanded clay concrete is an excellent and inexpensive option for those who want to move outside the city, especially if noisy Moscow has already become tiresome!

Preparatory work

Before starting construction of the fence, you should stock up on the necessary materials and tools. We will need the following building materials:

• Cinder block in the right quantity. The most affordable ones are ordinary, gray blocks. Along with them, torn, chipped, and colored cinder blocks are also produced. They have a rough surface that imitates wild natural stone.
• Components for preparing cement mortar and making a cushion: water, sand, crushed stone, cement.
• Rolled waterproofing (bikrost, roofing felt, stekloizol).
• Gravel, rubble stones, broken bricks, rebar. This is necessary for pouring the foundation.

From the tool you should prepare:

• Shovel.
• Trowel for laying mortar.
• Construction level, plumb.
• Roulette.
• Pegs and rope for marking.

When a cinder block fence is being erected, the entire construction can be represented in the form of several successive stages.

Subtleties of choosing blocks for a fence

A fence is the main attribute of any summer cottage. One of the main requirements for this design is strength and originality. Such parameters are typical for fence blocks. They are obtained from various solid materials with unique technical characteristics. Therefore, before purchasing this product, you should consider some of the subtleties of choosing blocks for the fence.

Peculiarities

Fence blocks are cubic artificial materials. They are made from various solutions, which, after hardening, form a strong and solid structure.

Outwardly, they resemble bricks and are large in size. Most fence blocks are hollow. This structure allows you to obtain an optimal ratio of strength and light weight. There are also solid products that consist of solid concrete or other mortar.

Blocks are a universal building material used to construct not only fences, but also small posts or fences. Some manufacturers produce them in the form of prefabricated elements, which, when joined, form a brick with empty space inside. These products make it easy to hide metal fence posts while creating a consistent post and fence style.

Advantages and disadvantages

Fence blocks are used everywhere in construction, as they have several advantages:

• The construction of fences is speeding up several times. This is achieved not only due to its larger size, but also to its correct geometric shape. Laying a rectangle does not take much time, since it is easy to level it in all planes.
• Low price. The blocks are made artificially, which reduces the cost of production compared to natural stone. This is also influenced by the large volume of the element, which can replace several bricks at once.

• Strength. This indicator may vary depending on the structure of the product. Some blocks tolerate frost well, do not absorb moisture, and can also withstand significant loads.
• Minimal care. Fences made from these products can be used for a long time without restoration. At the same time, the top layer practically does not lose its original characteristics.
• Variety of designs. Many manufacturers supplement the top layer with various decorative effects. This allows them to be used when creating original landscape solutions. The blocks combine perfectly with metal, wood and other building materials.

• The blocks do not burn and do not support combustion. This makes them safe for use in factories and other specific places.
• Durability. Some types of blocks can last up to 100 years, which is not always possible with brick or wood.

Which brick should not be used for the plinth?

Due to its high hygroscopicity, sand-lime brick is absolutely not suitable for arranging a basement. The base built from it will gradually collapse, since silicate perfectly absorbs moisture from the soil and is destroyed by temperature changes.

In just a couple of years, the basement will need a major overhaul. A collapsing base will, in turn, lead to the destruction of the foundation and, accordingly, the building as a whole.

Sand-lime brick: beautiful, but not suitable for a plinth Source bricknews.ru

Step-by-step DIY installation instructions

Before installing blocks for fence posts, mandatory measures are taken to prepare the area and concrete supports for a massive structure. They include excavation, concreting and provision of drying conditions.

Base structure

If a massive fence is planned along the entire perimeter, then a strip foundation is poured; in other cases, it is enough to form reliable foundations for each pillar separately.

Ready-made fence posts

The work is carried out in the following order:

1. After determining the required distance between the pillars and marking their position along the perimeter, they begin to dig holes. The depth should be slightly greater than the freezing level of the soil in the region where installation is taking place. The dimensions are 15 cm larger than the base of the elements in each direction.
2. The bottom is covered with a ten-centimeter layer of gravel.
3. Then a central metal pole is installed in the middle of the pit. It must be in a strictly vertical position.
4. The pit is framed with reliable formwork, either factory-made or made independently from boards of the required width, taking into account the above-ground part of 10–15 cm.
5. To strengthen the support, internal reinforcement is carried out.
6. A concrete mixture of cement, sand and crushed stone is poured in a ratio of 1:2:3.

During the pouring period, the remaining air should be eliminated and the composition should be compacted with a crowbar or a piece of pipe by stirring the concrete, and the assembly of the main structure should be carried out only after the base has completely dried.

Options for columns made from type-setting blocks

Installation of blocks

The concrete pillar is assembled in stages in the following sequence:

• with a one-piece design of the elements, one block at a time is strung onto the central metal post, but with a locking system, the assembly is carried out at the place where the fence is installed;
• connect the rows using a concrete mixture (sand and cement (3/1) with the addition of a plasticizer);
• if it is necessary to trace elements of electrical wiring or communications, a box made of thick plastic or metal is installed inside the pole;
• to give maximum strength to the structure, additional reinforcement is carried out before filling the internal cavity with concrete;
• the internal space is filled in stages, through the installation of three or four blocks;
• They finish the work by attaching the top cap, which prevents precipitation from entering the interior, since they contribute to the accelerated destruction of concrete in the “hot-freeze” temperature regime.

Scheme for installing typesetting blocks with your own hands

Work on concreting the base and assembling pillars should be carried out at an ambient temperature threshold of at least four degrees Celsius, otherwise the concrete will not be able to gain the required strength and will weaken the structure. If such an unforeseen situation occurs, you should use a special additive or use folk remedies.

One of the options for self-assembly of type-setting pillars is presented below in the video.

Peculiarities

A columnar-strip foundation combines the leading features of two types of foundations - columnar and strip. This combined option allows the construction of fairly heavy objects on unstable soils.

The supporting elements in this system are piles, which are dug into the ground below the freezing level of the ground and rest on hard layers of soil, bypassing soft ones. The strip concrete base takes on the load of the object, distributing it evenly between the piles. The tape binds the pillars without exerting pressure on the ground.

These types of foundations are suitable for unstable soils prone to heaving. First of all, these are clayey and fine sandy soils, organic soils (swampy, peaty), previously drained and drained. In addition, the use of piles allows construction to be carried out in areas with differences in height. In other words, the use of a pile-strip foundation makes it possible to make almost any site suitable for construction.

A strip foundation with pillars is similar in its principle of organization to its counterpart on piles, however, installing supports does not require the use of special equipment or drilling deep wells. This allows you to do the installation yourself and reduce the size of the estimate.

The advantage of columnar foundations is the ability to build on “problematic” soils, as well as in areas with differences in height. However, the design of such a system requires accurate calculations.

Making a strip foundation on pillars does not require a large amount of excavation work and is cheaper than pile analogues. A gap must be maintained between the columnar-strip base and the monolithic screed to minimize the impact of soil heaving on the foundation.

Creating a foundation based on pillars is not suitable for moisture-saturated soils (areas located in lowlands or near water bodies, soils with groundwater). For such areas, it is better to choose a pile foundation with a strip base.

From the very beginning, you should decide on the features of the building - its size, number of floors, technologies used. The material used to make the pillars, their number and diameter depend on this.

Typically, pillar foundations in combination with tape are used on unstable soils and are intended for small one-story houses with an attic or two-story buildings made of lightweight materials. Suitable wall materials are foam blocks and wooden structures (log houses), as well as “frameworks”, for the construction of which Canadian and Finnish technologies are used.

Types of typesetting blocks and their characteristics

The average weight of one block is from 10 to 25 kg. Length 30–50 cm, width 15–25 cm, height 14–25 mm.

Based on their composition and technical characteristics, they are divided into several types. Let's look at each of them in more detail.

Expanded clay concrete

Expanded clay is called clay that is fired at high temperatures. Thanks to the addition of expanded clay, the weight of the concrete block is reduced.

The choice of colors and textures is small. The surface is often rough. The shape is rectangular.

Decorative

Raw materials - clay, artificial stone, concrete and various fillers.

According to the design features there are:

They also produce decorative slabs for fencing, which allows you to quickly assemble modular structures that do not require finishing.

The surface of such blocks can imitate:

They are similar in structure and size to gas blocks and foam blocks. The price is affordable. Wide choice of colors.

Thanks to their original appearance and light weight, they have gained popularity not only in the assembly of fences, but also in the construction of houses and gazebos.

Construction

The raw material is pure concrete. They have impressive weight. There are cavities inside. The surface is smooth on top. Color – grey. Due to their unattractive appearance, they are rarely used when constructing fences in the private sector, more often as post material, or for fences at industrial sites.

They are light in weight. Frost-resistant. There are cavities inside.

Concrete

Another name is besser. Depending on the manufacturer, crushed stone, gravel, and screenings are added to the composition. These components strengthen the structure of the blocks, increase strength, and resistance to mechanical damage. Color – gray with shades. They are inexpensive.

Foam blocks

The composition may be different for each manufacturer.

Popular types are gas silicate and aerated concrete.

The structure can be solid or hollow.

When constructing fence posts, foam blocks are often used. This is due to its low weight and convenient size.

Dimensions of the standard block – 20*20*40 cm.

Often they take material whose surface imitates torn stone.

Finished sections and pillars made from blocks can be painted. You can learn more about the procedure and application nuances here: “Painting a concrete fence.”

Which brick is suitable for the plinth

If you follow the standards prescribed in clause 6.65 of SNiP, then ordinary solid red brick is universal for many regions; it is also called well-fired plastic-pressed ceramic brick. It is manufactured in accordance with GOST 7484-78 and TU and GOST 530-2007.

Solid brick with high density has a mass of 3-4 kg. Its volumetric weight is 1500 – 1900 kg/m3. It is used when it is necessary to organize high levels of structural strength, sound insulation, thermal conductivity and heat capacity.

Standard solid red brick Source terracot.ua

Decorative design

Today, many manufacturers are trying to diversify the style of blocks to give them an attractive look. This expands the scope of their application and makes similar building materials more popular.

Fence blocks can imitate several types of substances:

• Brick.
• Slate.
• A natural stone.
• Tile.

To add naturalness, the blocks are painted in different colors. Colored structures can be painted directly on site after installation. This approach is often used by designers to create unique structures and styles.

Particular attention is paid to shades that are present in nature

“Stone” products are suitable for almost any structure, as they can withstand high loads and are compatible with various construction approaches. If you use smooth blocks, then they can be decorated with additional finishing. It is easy to glue ceramic tiles, natural stone or apply decorative plaster to a concrete surface.

Monolithic pillars

Making monolithic concrete supports is a simple process. This is an opportunity to create a high-quality base for a fence yourself at minimal cost. The great advantage of a monolithic pillar is the ability to decorate it at your own discretion. The supports can be made of any shape - round, rectangular or square, the main thing is to assemble the appropriate formwork. To create the correct shapes, boards or plywood are suitable; for round supports, a plastic pipe sawn in half.

Installation of a monolithic concrete pillar

1. A hole is dug and crushed stone is poured onto the bottom.
2. A reinforcement frame welded from longitudinal and transverse rods is installed in the hole. The verticality of the frame is checked by the building level.
3. Concrete is poured into the hole and compacted.
   The hole is left to harden. Reinforcement of a hole for pouring concrete into a pillar
4. The formwork is being installed. The reinforcement cage should not come into contact with the formwork, but should be located exactly in the middle.
5. The formwork is filled in layers with a cement composition, each layer is bayoneted so that there are no air cavities left. After 3 days, the formwork is removed.

The resulting nondescript concrete pillar will be given a decorative touch by textured plaster, artificial stone or decorative brick.

Decorative stone for fence posts

Artificial stone is widely used for both interior and exterior decoration of buildings, foundations, finishing and cladding of fences and pillars. It is a composition of cement, sand and various additives and coloring pigments. Decorative stone perfectly conveys the texture and beauty of natural minerals and at the same time has a number of additional advantages that distinguish it from natural materials:

1. Price. Natural stone has a high cost compared to artificial material cast from concrete.
2. Ease. Decorative stone has less weight, it is easier to lay it on regular tile adhesive or cement without additional fastening. In addition, the lightweight material does not overload the supports.
3. Correct form. Thanks to its straight lines and geometry, artificial stone does not require complex fitting and selection of elements.
4. Resistance to negative natural factors. The facing stone is suitable for external work; it is not afraid of moisture, critical temperatures and exposure to ultraviolet radiation.
5. Variety of choice. The shape, color and texture of the artificial material can be any.

Decorating and painting

The facade of the fence made of gray cinder blocks needs plastering and painting. To do this, you can use ready-made (industrial) dry plaster mixtures prepared in accordance with the instructions:

• Mineral;
• Silicate;
• Silicone;
• Acrylic.

You can prepare the plaster yourself. The principle of preparing plaster is the same as when preparing masonry mortar. Only the proportion changes. They take less cement, more sand, and fluff lime is added as a filler.

A layer of plaster is applied 8–10 mm thick.

For painting, water-based paints are used (acrylic, silicate, latex, silicone, etc.). Their selection is wide, and prices vary.

Painting red

Painting yellow

The paint is applied with a paint roller in 1–2 layers, depending on the base and absorption into the plaster base.

What to look for when purchasing

When choosing bricks for the foundation, you need to pay attention to the accompanying documentation. The grade of stone must be higher than M150, frost resistance from F25, geometric dimensions must comply with GOST.

During transportation, unloading and storage, edges often break off, which is not a significant defect. In most cases, plaster waterproofing is used for brick foundations. Unevenness will only increase the adhesion of the protective layer.

When you tap a ceramic brick with a metal object, there should be a clear ringing sound, not a muffled dull sound. The ringing indicates the quality of the raw materials used, the correctness of the firing technology, and the absence of microcracks and voids.

Manufacturers

Many large enterprises, as well as private companies, produce sand concrete blocks on the Russian market. In the Moscow region you can purchase products that produce hollow and solid products. Partition and foundation modules of this type can be found at. You can also find the product you need at, “Pushchinsky Plant”.

In the regions, everything is also in order with the production of sand concrete blocks. One of the major suppliers is Ecostroy LLC from Kineshma in the Ivanovo region. Trust-Snab has its factories in Moscow and Kaluga. The Tula Concrete Concrete Plant, which produces blocks of various types, is no less famous among builders.

Types of blocks and their advantages

Finishing a concrete fence with plaster

The fence made from the blocks in question is easy to install. You don’t have to turn to professionals for help and do all the work yourself.

The advantages of such decorative products include the ability not only to create a solid fence, and thereby completely protect yourself from the prying glances of passers-by, but also to do without finishing it. In addition, such blocks resist open fire well, which means they are fireproof.

Solid block fencing

This material is not afraid of either low temperatures or high humidity. The dimensions of the products allow the installation of both a completely concrete fence and a fence consisting of different materials. For example, you can combine the material with wood, corrugated sheets, plastic and other materials.

The positive qualities of fencing made of such material include the following:

1. This is a reliable capital structure;
2. The decorative nature of the material used allows you to create a wide variety of types of fencing;
3. A fence made from expanded clay blocks is strong and durable;
4. It is not difficult to build such a fence yourself. It is enough to follow the sequence of work performed;
5. Concrete is not afraid of moisture, so it is not susceptible to rotting and mold;
6. Fencing made from such blocks can withstand wind loads and other aggressive environmental influences;
7. Concrete fencing is fireproof.

Upon completion of the construction of the fence, its surface can be painted in any color.

Hollow decorative block

It is important that this paint is resistant to environmental influences and is intended for painting concrete surfaces. On the modern building materials market there are many different types of material with a decorative surface

Concrete fence blocks

Thanks to this, you can implement any design ideas.

Decorative items

The disadvantages of this building material include its heavy weight. One element has a mass of at least 30 kg, and there are also more massive products.

The structure turns out to be very heavy and therefore requires the creation of a solid foundation. Therefore, it is impossible to do without additional financial costs. But still, such a material has much more positive properties than negative ones.

Blocks for concrete fences

Main characteristics

Fence elements. A standard decorative product has dimensions of 480x320x150. Its surface can be simple, looking at which you can immediately understand that it is concrete.

Some sizes of decorative items

But there is also a material with a surface that imitates crushed stone. This material goes well with spans made of wood, metal, plastic, and PVC.

Product range

Fencing made from decorative blocks fits perfectly into any design. The product is the main element in the design of the support column. In shape it is a rectangular parallelepiped.

Decorative blocks are produced by vibration pressing. Cement acts as the main binder. Often additional components are added to the concrete mixture: crushed stone, gravel, brick.

Some decorative material options

Types of decorative blocks

There are several options for decorative products:

What are they for?

Over the hundreds of years of civilization, humanity has come up with many ways to organize cordons of personal territory, but until today nothing better than stone blocks for a fence has been invented. Another thing is that today it is often not natural stone that is used, but its somewhat cheaper versions, which involve the use of one or another filler, but in general this does not affect the strength.

Stone blocks, even of artificial origin, are powerful and reliable. The presence of any filler does not greatly affect the strength of the constructed wall and the owners can be sure that intruders will definitely not break such a fence. In order to destroy such an obstacle, you need special equipment, and robbers of any level are unlikely to decide on such a risky undertaking.

If previously only the most powerful of this world could afford such a luxury, today any person who has his own personal plot is able to give his family a feeling of complete security thanks to the construction of such an engineering miracle. Such opportunities have arisen thanks to rapid progress. For example, previously stone blocks had to be searched for in the surrounding nature and then delivered from the nearest deposit to the customer’s location.

Nowadays, industrial enterprises press any available filler with the addition of cement to a state where the final result is in no way inferior in reliability to natural stone. Moreover, the owner can even install the fence with his own hands, which will significantly save the cost of its construction. At the same time, the procedure is not so complex and lengthy that it requires relying on called specialists, which further reduces the cost of the project.

Form

Today, all types of fence blocks are rectangular in shape. But they can only differ in the structure of the top decorative layer. The simplest products are made with a smooth surface. The advantage of such options is their high-quality joining during installation.

Externally, they do not carry any decorative load and are used only as a building material in places where decoration is not so important

Particular attention should be paid to the decorative block, which has a torn surface. On the surface of these products, a rough structure is formed piece by piece, which resembles crushed stone (the second name of these products)

With the help of such products it is easy to imitate almost any texture of natural materials. But the cost of such a block is much lower than natural products.

Construction cost

Among them:

• foundation type;
• materials used;
• required load-bearing capacity and stability - the higher the required indicators, the higher the costs will be;
• attraction of specialists and special equipment.

The cost may be influenced by external factors, including the need to develop in uneven terrain. The type of soil is also important. An example would be increased costs if soil resistance is weak or there is a nearby aquifer.

On construction sites you can calculate the cost using a calculator. The average price per linear meter is 600 rubles. Read more about the cost and its calculations in this article.

Advantages of a cinder block fence

Fences are built from cinder block relatively rarely, considering them too labor-intensive. However, such structures are built to last for decades, unlike other materials. We list the main advantages of such construction:

• Extraordinary durability of blocks, amounting to more than 50 years. If the outside material is additionally lined, the building will last much longer.
• A cinder block is one and a half times lighter than a brick, so the load on the foundation is reduced.
• Relatively low cost compared to other solid materials. The cost of construction is further reduced if the blocks are made by hand.
• The fence can be given a decorative look by facing it with ceramic tiles, which fit perfectly on this material.
• Environmentally friendly building material that does not harm people and nature.
• Construction can be done with your own hands, without the involvement of craftsmen.

Conclusion

So we found out why a base is needed in general, and made of brick in particular. And the last piece of advice from our experts is to choose only high-quality materials for the basement, because the reliability and service life of your home directly depends on the quality of this structure. Also, you shouldn’t do the masonry yourself if you don’t have at least minimal skills: it’s cheaper to hire specialists than to carry out a major overhaul in 5-10 years, at best of the base, or at worst, along with the foundation.

(75 votes, average: 4.7 out of 5)

Help us make the article better, tell us what is the reason for the low rating?

Share with your friends: