Manufacturers are constantly improving plumbing fixtures, trying to make their use as comfortable, practical and cost-effective as possible. One of these solutions is a thermostatic mixer for bath and shower, eliminating the need to constantly adjust the water temperature.
Agree, it is very convenient to configure and fix the optimal parameters for yourself, so as not to waste time over and over again selecting the desired position of the lever. Ease of use is obvious, isn't it? It remains to decide on the mixer model.
We will tell you what parameters you should focus on when choosing a thermostatic device, outline the features of different versions, list the best manufacturers, and also note the nuances of installing a faucet.
What is a thermostatic mixer?
Residents of European countries have long been accustomed to saving natural resources and try to use them wisely. Therefore, it is not at all surprising that our western neighbors actively use temperature sensors and regulators in their everyday life, including faucets with thermostats for bathrooms with showers.
This solution provides an opportunity to save money without limiting yourself in using all the benefits of civilization.
Features and principle of operation
As a rule, in a mixer that maintains a certain water temperature, it is enough to select the pressure and indicate the desired temperature regime. And then the technician can handle it on his own - the command is sent to the sensitive element through the fastening and adjusting screw. This can be a bimetallic strip or wax.
The substance, depending on the specified settings, expands or contracts, which leads to a change in the position of the valve, which allows water to enter the mixing chamber. The adjustment occurs quickly and clearly and does not require further action on the part of the user.
Modern faucet models are also equipped with a water pressure regulator. It turns the flow off/on and makes it as comfortable as possible at the exit.
The water temperature is controlled by a special limiter. The element ensures that it is not higher than that specified by the consumer
The thermostatic device operates using a sensor located directly in the device body. Hot water and cold water enter the mixing compartment through a distributor. The stream then rushes to the tap.
If the water temperature is lower or higher than that set by the user, the sensor automatically adjusts the locking mechanisms. This allows you to adjust the volume of hot and cold flows.
If the water has a temperature that is much lower than that specified by the consumer, then its supply will be automatically stopped
Advantages and disadvantages of devices
Compared to other types of faucets, a thermostatic device can significantly reduce hot water consumption. This is especially noticeable if an electric boiler is installed in the house or apartment.
Precise temperature control makes it possible to use comfortable water, eliminating long-term adjustment of the desired parameters. And this, accordingly, reduces the amount of electricity required to operate the heating device.
The list of advantages of this type of faucets should also include the fact that the consumer will not be scalded and will not face an icy shower. Therefore, it will become indispensable in a house where there are small children.
When using an instantaneous water heater, the water temperature may change regularly. This is the main and only drawback of such equipment. The problem is solved by installing a thermostatic mixer, which will allow you to enjoy your bath.
If you install such equipment, you will no longer have to depend on your neighbors constantly turning the water on and off in their apartment. Now you can shower no matter what.
The only disadvantage of faucets with a thermostat is their high cost. But savings, safety and level of comfort completely offset this disadvantage
Features and functions of electronic models
A bathroom faucet with an electronic thermostat is a more expensive and technically complex model that requires batteries or an AC adapter. When choosing water temperature and pressure, there are electronic temperature and pressure sensors that not only regulate the water supply automatically, but also display the indicators on special screens. They can have push-button, touch, or remote control. But in everyday life such equipment is unnecessary.
Mixer with electronic thermostat
Types of thermostatic mixers
Today, the range of devices that supply comfortable water for bathing is regularly increasing. Manufacturers are ready to offer faucets with thermostats for bathtubs, showers, sinks, and bidets. However, the models differ in the method of fastening. For example, there are devices for visible and hidden installation.
In general, devices are divided into two groups: mechanical and electronic. This factor must be taken into account when choosing. After all, representatives of each of these two groups have both advantages and disadvantages.
Devices with mechanical adjustment
The simplest and, accordingly, cheapest is the mechanical model. This mixer is equipped with valves, levers and handles that allow you to regulate the strength of the water flow and its temperature.
Devices with mechanical adjustment are much more reliable and durable. At the same time, they work faster, since the temperature is switched manually. As for the price, the cost starts from $60.
The disadvantage of mechanical thermostatic mixers is the peculiarity of manual setting of parameters. But if you need the most simple and inexpensive plumbing equipment, then this minus plays absolutely no role.
The design of mechanical equipment is usually minimalistic and does not contain any unnecessary parts, which makes it easy to operate
Electronic thermostatic mixers
If the house is being furnished in modern style, then it is better to give preference to electronic equipment. In most cases, such faucets have a laconic and elegant appearance that will harmoniously fit into any interior.
In addition, electronic models are equipped with a screen based on liquid crystals, which shows the current water temperature, as well as the pressure force.
Such mixers are controlled using mechanical or touch buttons. There are also contactless devices on the market that operate using infrared sensors. They are often controlled using a special remote control.
If we talk about the advantages of electronic thermostatic mixers, then the advantages include:
- comfort - they allow you to indicate the water temperature with an accuracy of up to 1°C;
- attractiveness - electronic models look modern;
- multifunctionality - they can display many additional parameters.
But it should be taken into account that electronic equipment will cost several times more than mechanical equipment. Moreover, due to the complexity of the design, it is quite difficult to install such mixers correctly. And in the event of a breakdown, you will have to call a qualified specialist, which will also hit the family budget.
The electronic thermostatic mixer requires a power supply. Batteries or an AC adapter can be used for this.
Grohe
The Grohe bathroom faucet with thermostatic shower has been on the plumbing market for a long time. There is a huge selection of different mixers here. The faucets of this company differ not only in their functions, but also in their appearance. Therefore, here you can choose a mixer to suit your interior. The main material used to make these devices is brass. According to user reviews and expert estimates, on average, the mechanisms of this company will serve your home for about ten years. Here you can choose multifunctional devices that will cost 45 thousand rubles, or you can choose something more budget-friendly from 1.5 thousand rubles.
Main selection criteria
A huge assortment of faucets with thermostats creates a lot of problems for the unprepared buyer. After all, choosing the optimal model from this variety is quite difficult and it can take more than one hour.
What to look for before buying?
To find a device that will allow you to shower comfortably, will last at least several years and will not stand out too much in the bathroom design, you need to pay attention to a number of parameters.
Important characteristics:
- material used to make the case;
- valve type;
- presence of a fuse;
- connection method;
- minimum possible working pressure;
- manufacturer.
Before going to the store, it is recommended to familiarize yourself with the products of online stores. This decision will allow you to decide in advance on the optimal model for your bathroom.
Case material
The service life of the mixer largely depends on the reliability of the housing. Accordingly, this factor must be given attention first.
The most reliable and, accordingly, expensive materials are considered to be brass, bronze, and copper. If the appearance of the faucet comes first, and not its strength, then you can give preference to a ceramic product.
Manufacturers also offer models made of plastic and aluminum-silicon alloy (silumin). Yes, these devices are quite cheap, but they will not last very long.
Which valve is better?
An important component of any thermostatic faucet is the valve. This element is often made of ceramic, rubber or leather. The last two materials are used to produce cheap models, which is why many problems arise.
A leather or rubber valve wears out very quickly. This can cause many unpleasant situations in the future. But replacing such a part will not be difficult. The procedure is similar to the process of replacing the gasket in a regular faucet without a thermostat.
Leather and rubber are soft and short-lived materials. It is because of this that quite often a problem arises associated with damage to the valve seat. If solid particles get under the element from the water, the part is damaged, which leads to a flood. Therefore, if you find any problems, you must urgently contact a specialist.
A ceramic valve is more reliable and durable. In this case, a special design prevents debris from getting under the element and, accordingly, the saddle remains intact.
The ceramic valve pushes out all solid particles trapped under it. Moreover, the element has a graphite coating on top, which significantly extends the service life of the mixer.
When operating thermostatic equipment with a ceramic valve, do not use brute force when closing the valve. Failure to comply with this rule will result in the faucet head breaking.
Therefore, to shut off the water flow, you should turn the valve all the way, and the ceramics, precisely adjusted to size, will do the rest.
Why is a safety button needed?
Every more or less well-known manufacturer of thermostatic mixers installs a fuse in their products. This element prevents accidental changes in water temperature. After all, there is always a risk that with one awkward movement you can turn on boiling water and get severe burns.
Most often, the element is made in the form of a button, painted red. In this case, to change the water temperature, you need to release the fuse. This useful feature will be especially relevant for parents with young children.
Mixer connection diagram
When choosing plumbing equipment with a thermostat, it is imperative to ask the seller about the connection diagram for the water pipes to the device. After all, if you connect everything incorrectly, the mixer will break and will need to be repaired, which, as mentioned above, will be quite expensive.
To connect a thermostatic mixer in a bathroom or shower, you can use flexible hoses
Check that the equipment is adapted to Russian standards. Remember that one question will eliminate the need to change the pipe configuration.
Minimum operating pressure
An important characteristic is the presence of sufficient water pressure in an apartment or private house. The vast majority of devices operate at a pressure of 0.5 bar.
If in fact it is lower, the equipment will not function properly. Accordingly, there is simply no point in installing it in your bathroom.
Which manufacturer is better?
The plumbing equipment market is regularly updated with new products. But if you need to purchase a thermostatic mixer of the highest quality, then the best solution would be products from Oras , Jacob Delafon , Grohe , and Hansgrohe .
For the average buyer, products from the Oras . The company always tries to maintain the most favorable balance between product quality and affordability. In production, the company primarily uses plastic or brass.
The cost of thermostatic mixers from Oras is relatively low and amounts to about 180-200 dollars
Since its founding, the French manufacturer Jacob Delafon has established itself as a reliable supplier of brass plumbing equipment. Its distinctive feature is the provision of a five-year warranty on all faucet models.
As for appearance, Jacob Delafon products have a classic design. Equipment costs typically range from $150 to $450.
Grohe boasts the largest range of faucets . This manufacturer offers products equipped with a wide variety of functions and made in various styles.
Grohe uses brass in production. Therefore, it is not surprising that faucets from this brand last at least 10 years.
Although Grohe products differ from their analogues in quality and reliability, they are quite expensive. On average, the price of faucets from this brand is $300-700
Hansgrohe , also deserves respect . Their thermostatic mixers are distinguished by their most laconic design and high durability. Chrome plated steel is used for the manufacture of products.
Hansgrohe faucets are the ideal solution for small bathrooms. After all, the equipment is compact and relatively inexpensive - around $200.
Hansgrohe provides a 5-year warranty on all its products, which is quite good considering the stated price.
Almost all manufacturers offer the buyer several lines of mixers with thermostats. The assortment includes simple models, the design of which focused on their functionality.
But the catalog often includes several products that represent a real work of contemporary art.
What is a shower thermostat and why is it needed?
Many people have heard about such a device as a thermostat for a bathroom or shower, but do not have information about what it is. At the same time, this device provides great comfort and safety for taking water procedures, so everyone will need it. So, a shower thermostat - what is it, and how is this device justified in our apartments?
In this article we will take a detailed look at this device, the principle of its operation and the highlights of the installation.
What is a thermostatic mixer
What is a thermostat for?
In simple mixers, as we know, you have to regulate the flow pressure and temperature yourself. Moreover, during bathing, you often have to adjust the water, since it becomes either cool or, on the contrary, unbearably hot. This is due to the difference in pressure of cold or warm water in the system.
This phenomenon is not only unpleasant, but also scary, since while taking a shower it is possible to get a serious burn. The thermostat, or as it is also called, the thermostatic mixer, allows you to avoid similar problems.
Thus, a thermostat is a device that controls and regulates the flow of cold and warm water, maintaining the pressure and temperature of the flow at a user-specified level.
Principle of operation
So, we have figured out the purpose of the thermostat, now we will look at how this device works. To do this, let's first get acquainted with its main elements.
Any bath and shower thermostat consists of two main elements:
- A handle with a scale with which a certain level of flow temperature is set.
- A thermostat that controls and regulates the process of mixing cold and warm water. The main elements of this device are paraffin and bronze rods. The latter has a plastic cylinder.
The operating principle of the thermostat is quite simple:
- As the temperature of the flow increases, the paraffin rod, which reacts to each temperature change, expands.
- As a result of the expansion of the paraffin, the bronze rod is pushed out, which leads to an increase in the space (cold water passage) between the metal body and the plastic cylinder of the thermostat.
- Since the pressure of cold water increases, and the pressure of hot water, on the contrary, decreases significantly, the flow temperature decreases.
- As the water temperature drops, the paraffin shrinks, and accordingly the passage of cold water is significantly reduced.
Thus, the flow temperature is maintained at the same level. This process is continuous, based on this sensation, we accept the temperature of the flow as constant.
Please note that the thermostatic mixer has two handles - for adjusting the water temperature and adjusting the flow pressure. The latter is a regular valve that allows you to completely shut off the flow.
Advice! Before taking a shower, it is recommended to first set the optimal water temperature, and then adjust the pressure. If necessary, it is possible to adjust these parameters while taking a shower.
In practice, in most cases, it is enough to adjust the temperature once, after which it is possible to use the shower only by turning on the water supply.
Device Features
Advantages
This device has many positive aspects:
- Completely excludes an increase in temperature to a critical level . The same applies to its reduction. That is why taking water procedures is safe and comfortable.
- The surface of the mixer does not heat up to a high temperature , therefore, touching it, you will not get burned.
- High flow temperature does not exceed 43 degrees.
- If the flow of cold water stops, the flow is completely blocked.
In addition, it should be emphasized that a thermostat is much easier and more ergonomic to use than a simple mixer.
Flaws
There are perhaps only two disadvantages to this device:
- Higher price than simple faucets. Indeed, it is possible to say that the high price is fully justified.
- Sensitivity to water quality. Based on this, it is recommended to install water softeners and filters in front of the mixer. Otherwise, the device will quickly fail.
Otherwise, the device has no shortcomings.
Recently, various shower systems have been equipped with thermostats. Below we take a look at all their types:
In most cases, these devices are used for bathrooms, since the shower in this case is more of an additional option than the main one.
The stand can be installed both in the bathroom and in a stationary shower. In the second case, the device is possible without a spout.
In most cases, a thermostat built into the shower panel is used.
It must be stated that every shower system with a thermostat, whether it be a stand or a panel, works on the same principle, which is outlined above. Based on this, the choice depends only on the purpose of the shower system and your wishes.
Advice! If the size of the restroom does not allow installing a bidet next to the toilet, a good alternative to this plumbing fixture is a hygienic shower with a thermostat, which is installed on a simple toilet or a wall near it.
Installation features
The main condition for connecting a thermostatic mixer is the correct placement of warm and cold water pipes. Let us emphasize that in most Soviet-style houses, communications do not meet the requirements of thermostats. Based on this, the installation of the device should be taken care of even at the stage of renovation in the bathroom.
Subtleties of installing a device with a thermostat
Installing a faucet with a thermostat in the bathroom is a fairly simple process that can be handled without the involvement of a qualified technician. Moreover, the parameters and requirements for its installation are the same as for standard valve models.
When doing installation, first of all, you need to ensure that hot water is supplied to the mixer at the same time as cold water. In addition, you must adhere to the installation diagram. If you make a mistake, the mixer will not work.
Installation can be carried out in two ways:
- open;
- closed.
Open method . There are no particular difficulties during installation. After all, all you need is to connect the hoses and secure the faucet to the wall, sink, bathtub rim or shower stall.
Closed installation . In this case, you will need to install an additional false wall made of plasterboard. After all, it is necessary to ensure that only levers or buttons that regulate the temperature stick out from the wall.
The only disadvantage of hidden installation is that in case of a breakdown you will have to open the wall
If we compare two methods of installing a mixer, then each of them has its own advantages and disadvantages. But in the case when high-quality thermostatic equipment was purchased, it is recommended to engage in hidden installation.
After all, then the bathroom design will be freed from unnecessary details, which will make the interior more harmonious and luxurious.
How to install a faucet in the bathroom?
Many people think that models with a thermostat heat the liquid by connecting to electricity. This opinion is wrong.
When connecting, the following order is observed: hot liquid is supplied to the left side, cold liquid is supplied to the right. If these requirements are not met, the thermostatic device will not be suitable for use.
Installation of the mixer consists of the following steps:
- Close the valve;
- Clean and lubricate shut-off valves to shut off the flow;
- Remove the old device;
- Check the integrity of the disks and threads of the installed equipment;
- Twist the eccentrics;
- Clean the discs from dirt;
- Wind the fume tape onto the thread of the device;
- Install gaskets;
- Install decorative trims;
- Secure the device;
- Carefully apply sealant to the joints;
- Open the liquid valve and check the functionality of the equipment;
- Adjust temperature.
Advice! Before starting the installation, it would be a good idea to install filters at the entrance of the pipes into the apartment. This will enable the device not to fail longer.
The best producers are recognized as Germany, Italy and Türkiye.
Some useful tips
To ensure safe operation of a faucet with a thermostat in a bathroom, it is necessary to install additional cleaning filters. This solution will be especially relevant if the water in the mains is hard.
Yes, installing filters will take time, but in the future this will avoid unplanned expenses and significantly extend the service life of plumbing equipment.
As a rule, centralized water supply is merciless to modern and fragile plumbing. Faucets with thermostats are also at risk. Sudden and sharp changes in pressure, water hammer on the main line, poor water quality - all this can significantly reduce the service life of plumbing equipment.
This problem is solved by installing a pressure reducer or check valve at the entrance to the apartment water supply system. After installing the elements, do not forget to adjust them in accordance with the operating parameters of the purchased mixer.
To ensure that the water temperature does not differ from that indicated on the valve, the thermostat must be calibrated. The setting is carried out using a special screw, which can be found under the protective cover of the device. To do this, you will need a regular screwdriver and a household thermometer.
Grohe thermostats are good, but that's not all there is to know about them
Some visitors to the San-premium.ru store tell us that they have heard or read that Grohe thermostats are considered the best, and therefore ask to explain why the Grohe thermostats are better than others. We do not conduct expert product ratings, so we leave the first part of the question without comment, but we will be happy to share the known details about Grohe thermostats.
The very name thermostat, or as they also say - thermostatic mixer, implies that it makes the temperature (“thermo”) “static”, that is, stable and constant. Anyone who has tried to wash in the shower, constantly turning up the taps so as not to get burned or freeze, has a general idea of the “responsibilities” of a thermostat, and with a sufficient level of education could invent one. On the other hand, the thermostat, as such, has already been invented, but like any mechanism it has its strengths and weaknesses.
Since the Grohe thermostat must maintain the temperature of the leaving water selected by the user, it is also entrusted with the mission of solving all problems associated with fluctuations in temperature and water pressure in the water supply. For several reasons, being too demanding on your thermostat can be unhelpful and even destructive. So, what you shouldn’t expect even from such well-known and popular thermostats as Grohe:
- the thermostat does not heat the water, so water cannot flow out of it that is warmer than it enters from the water supply;
- the thermostat does not filter the water, so if the water is dirty, it will work until the thermocouple or check valves become clogged with dirt;
- The thermostatic cartridge with thermocouple mixes hot and cold water even when not in use. The thermostat reacts to any changes in the parameters of the incoming water, and so that it has a constant opportunity to mix the required volumes, check valves are provided. Through them, the thermostat pushes excessively cold or hot water back into the water supply. If the check valves are faulty, the thermostat cartridge will be constantly pressed by water from the water supply and it will not be able to “cool” or “heat” the water, since there will be no room in it to add water of the appropriate temperature, and as a result it will not differ much in function from a conventional mixer;
- All Grohe thermostats are set by manufacturers at the factory for use at 15ºC cold water and 60ºC hot water, and the water pressure should be 3 bar. Standard parameters of Russian water supply networks differ from (for example, pressure is up to 4 bar, and hot water temperatures can start from 50 degrees), and actual indicators depend on utility services and the correct settings of boilers. Therefore, for the correct operation of the thermostat safety stop (indicated by the 38ºC level), it is necessary to configure the device in accordance with real conditions. The setup is simple enough that a user without special education can master it, and to carry it out, only a thermometer is needed among the “special tools”;
- a safety stop fixed at 38 degrees means that you cannot get hotter water by accidentally turning the knob, so to supply hot water from the tap you must remember to press the special button on the thermostat;
- The standard water supply to the thermostat is meant to be “hot on the left and cold on the right” (looking at the thermostat). But if it is impossible to fix the water supply network, then you will have to additionally purchase and install a “return cartridge”. Otherwise, the thermostat will not work;
- Grohe thermostats are not designed to work with instantaneous water heaters if their power is less than 18 kW;
- Well, returning to the beginning of this list, let us remember that the thermostat does not heat the water, and that check valves interrupt the direct connection of the thermostat with the water supply system, therefore, if there is a danger of water freezing in the water supply network and draining it from there, it is also necessary to remove the thermostat, since the water the thermostat will not drain on its own (without appropriate pressure), and ice can damage the cartridge.
Conclusions and useful video on the topic
The video shows an easy way to install a thermostatic shower mixer:
Thermostatic mixers have not yet gained much popularity among domestic buyers. The reason for this lies in the high cost of equipment. But those people who spent money on this plumbing equipment note the safety and ease of use of such a device.
Moreover, the invested money pays off quite quickly, since the mixer saves energy and significantly reduces hot water consumption.
Looking for a thermostatic mixer? Or do you have experience installing and using such a device for a bath and shower? Please leave comments on the article, ask questions and participate in discussions. The contact form is located below.
Comparison of characteristics and prices
Those wishing to purchase a high-quality faucet with a rain shower and spout can refer to the following table. It will allow you to find out the important technical characteristics of the best products.
| Model | Shower stand height, cm | Diameter of overhead shower, mm | Hand shower modes | Average price, rub. |
| Rossinka Silvermix S35-46 | 158.5 | 200 | 5 | 11 838 |
| Gappo G2491 | 145 | 250 | 1 | 12 841 |
| Lemark LM0462C | 164 | 16 824 | ||
| KAISER Cuatro 58182 | 87.5 | 200 | 3 | 18 750 |
| IDDIS Edifice EDISB3Fi06 | 124.5 | 232 | 25 990 | |
| WasserKRAFT A17701 | 115 | 220 | 28 760 | |
| Timo Beverly SX-1060 | 137 | 260 | 1 | 31 046 |
| AM.PM Like F0780964 | 135.5 | 254 | 3 | 29 590 |
Rating of hygienic showers
To compile the review, experts selected plumbing fixtures from well-known brands. Installation features and functionality were studied. The opinions of builders, designers, hygienists, and user reviews were taken into account. The main attention was paid to the following parameters:
- Design – valve, lever, thermoregulatory models are produced;
- Materials - brass, stainless steel, chrome steel - differ in properties;
- Installation - connect to a bidet, sink, install in a separate cabinet, on the wall;
- Complete set – hose, wall holder can be supplied separately;
- Mixer – hidden and wall installation options were considered;
- Water supply - models with a button and a foot pedal are offered.
Leakage, incorrect operation of the cartridge, unreliable hoses - plumbing fixtures with such characteristics were excluded from our rating.
The best hygienic showers with built-in mixer
Equipment with a built-in mixer makes the hygienic shower in the toilet completely autonomous. The user can choose a comfortable temperature and adjust the pressure. Models with lever cartridges and valves are available in a variety of styles. This allows you to choose a set for a bathroom with any interior and layout. VyborExperta.ru recommends four models.
Grohe BauCurve 124899
Ready-made kit with mixer for concealed installation. The shut-off valves are installed in the wall, leaving only a lever on the surface to control the cartridge. The adjustment is simple and precise; you can set the minimum flow rate to no more than 2.5 liters per minute. The socket and lever seals are made of durable materials. There is an additional temperature limiter.
Shower hose 1.25 meters long in a reinforced design with high tensile strength and protection against creases. The chrome surface is easy to clean due to its smooth structure. The push button control is conveniently located. The presence of an internal cooling channel increases the service life. The hose mounts are universal, this allows you to choose an accessory with any other length.
Advantages:
- Anti-limescale system;
- High temperature resistance;
- Withstands pressure up to 12 bar;
- Rotary cone;
- Scratch-resistant surface.
Flaws:
- Not detected.
Nobili AV00600CR
The Italian hygienic shower for the toilet has a single-lever control system, which is distinguished by accuracy, reliability, and long service life. The installed cartridge is made of wear-resistant ceramics, which allows you to maintain stability of adjustment during prolonged use. The temperature switch lever is convenient and small in size.
The watering can is made of a brass-based alloy and is characterized by increased strength and ergonomic shape. The diffuser makes the water flow neat and comfortable for delicate procedures. All elements have a chrome coating, on which splashes do not leave stains. A 120 cm long hose is supplied as a set; it attracts attention with its original braided design.
Advantages:
- Easy installation;
- Elastic pads;
- Smooth adjustment;
- Balanced design.
Flaws:
- Not designed for constant shut-off pressure.
Lemark Plus Strike LM1119C
The single-lever built-in model attracted attention with its quality of execution. The watering can is made of durable brass that is resistant to temperature changes. A convenient location has been chosen for the control key; anti-slip material is used in the manufacture of the button. The diffuser forms a structured stream of water that has a delicate effect on the body.
The mixer with an ergonomic lever is designed for installation in a false wall. The hose is supplied as a set, length 150 allows the equipment to be used in large bathrooms and combined bathrooms. Double elastic braiding reliably protects against damage. The threaded connections are well designed and ensure a tight connection. All elements are coated with chrome, which gives the equipment an aesthetic appearance and simplifies regular maintenance.
Advantages:
- Smooth adjustment;
- Does not leak;
- Balanced watering can;
- No sediment forms on the diffuser.
Flaws:
- Not detected.
Oras Polara Set 1488
Finnish plumbing stands out for the high quality of the fittings used. This is of particular importance for hygienic showers with concealed mixer taps. For installation, it is enough to use the services of a plumber once and the shower will last at least 10-15 years. The watering can is made of heat-resistant brass that can withstand heat up to 80 degrees. The original shape of the control key makes use comfortable.
The kit includes a 1.5 m long hose; double braiding protects against temperature deformation and mechanical damage. The handle is marked for cold and hot water, and its shape allows for smooth, precise adjustment. The design is made in an urban style and goes well with sanitary equipment from European manufacturers.
Advantages:
- Durable holder;
- Large round rosette;
- Does not leak if the rules of use are followed;
- Withstands pressure up to 10 bar;
- Good pressure.
Flaws:
- Overcharge.
Which hygienic shower is better
Buyers have different requirements for plumbing fixtures, bathrooms differ in layout, and repair estimates differ in budget. Finding a universal solution is difficult; our experts recommend taking into account the interior features, installation conditions, and equipment price. The VyborExperta.ru team recommends the following brands:
- Frap F7503 – for budget repairs;
- Jacob Delafon Cuff is the choice of users who are looking for a lightweight watering can;
- Grohe BauCurve – option for an embedded system;
- Oras Polara Set – for those who value quality and durability;
- Oras Optima is the best option with a thermostat.
All presented models are worthy of the attention of owners of private houses and city apartments, but only the most user-friendly plumbing fixtures deserve the title of best in their class.
