How to make construction trestles with your own hands: overview of options + video and photo

From this master class you will learn how you can independently make the now popular folding pair of trestles for a portable workshop.

The design is quite simple, made from inexpensive materials. All necessary drawings are presented for manufacturing, as well as a cutting blank in the Sketchup program.

At the end of the work the author also talks about that. how to make simple mounts for hanging sawhorses on the wall from

• Materials and tools
• Drawings for manufacturing
• Making goats
• Tests
• Making fasteners for hanging
• Storage

Do-it-yourself production budget

For trestles with a height of 0.8 m, the following dimensions are valid:

• legs (4 pcs.) – 0.95 m
• top crossbar – 0.9 m
• spacers (3 pcs.) – 0.85 m, 0.77 m and 0.7 m

Therefore, to manufacture two sets of devices you will need lumber and fasteners in the following quantities:

• board 95 x 45 mm – 5 pieces 2 m each
• board 90 x 20 mm – 1 piece 2 m
• board 90 x20 – 1 piece 3 m
• furniture bolt M10 x 100 with nut – 4 pieces
• M10 washers – 12 pieces
• self-tapping screws 4 x 45 – 50 pieces (for wood)
• belt – 2 pieces

Attention: The main problem when buying boards is choosing dry wood with stable geometry. The trestles do not have a rigid frame, so “propellers”, boards with a difference in thickness, or chips are not suitable

An approximate estimate for the production of universal folding trestles is as follows:

• belt – 140 rub. (2 pieces per pack)
• bolts included – 75 RUR.
• self-tapping screws – 30 rub.
• board – 1000 rub.

You can meet the amount of 1.25 thousand rubles, that is, at least four times cheaper than when buying ready-made trestles.

Calculations and materials

You can buy sawhorses, both folding and regular, in almost any specialized store. But they most often have an aluminum base and are quite expensive. It is much easier and cheaper to make trestles for your dacha with your own hands. This is a relatively simple design that requires a minimum of carpentry skills from the manufacturer. In addition, homemade goats will not cost you a pretty penny, they can be easily adapted to the construction project you need, and they can also be easily used in the future if desired.

Goats from the store

You can assemble both metal and wooden trestles yourself. But we still recommend choosing the wooden version. Wood is much easier to work with and cheaper.

One of the first stages of work is the design and creation of a drawing. We strongly recommend that you do not carry out all the work “by eye” - it is very easy to make a mistake due to which your structure will turn out to be crooked and unstable. Well, or it won't work at all. Therefore, sketch out a detailed drawing on a piece of paper indicating all dimensions, immediately write down how much fasteners you need and how much base material you need. The drawing will also clearly allow you to see what the finished structure will look like.

A simple drawing of a folding trestle

At the first stage, it is important to determine the height of the future goats. Usually it is chosen depending on the person’s height

Traditionally, the height varies between 75-95 cm.

Your favorite desktop or workbench will also help you determine the height. If you have one and you often work with it and feel comfortable, then you can measure its height and make a sawhorse with exactly the same parameters.

Universal sawhorses

The support legs of a goat must be assembled at a certain angle relative to each other. This will increase the stability of the structure. Let's take the standard version with angles of 65 and 80 degrees. Based on the height and angles of the legs, it is already possible to calculate the parameters of the remaining parts. Thus, it turns out that for one goat you will need:

• legs 95 cm long - 4 pcs;
• upper support crossbar 90 cm - 1 piece;
• spacers - 2 on each side.

In addition, do not forget to buy fasteners. These are bolts, nuts, washers and screws. These elements will allow you to assemble a reliable structure. We do not recommend using nails - connections with them are less reliable and durable than with self-tapping screws. Nuts and bolts will be needed to connect the folding legs.

You can buy wood for the goats at your nearest hardware store, but you can also look at all sorts of scraps at your dacha. You most likely have them if you have done any construction work before. The board is suitable size 100x30 mm.

Do not use wood with obvious defects to create a goat.

Types and components of metal scaffolding

When building a house from stone or building blocks, metal scaffolding is more suitable. They are able to withstand any load. They are less popular only for the reason that in many regions wood is still the cheapest type of building materials. The second point, which is often decisive, is that after dismantling the wooden scaffolding, the boards can be put to work - used in further construction. And metal parts should gather dust in the shed.

But metal scaffolding also has its advantages. When disassembled, they do not take up much space. Owners of wooden houses still have to use them periodically: the log house requires maintenance, so scaffolding is needed every two to three years. In this case, it is more practical to use metal rather than wooden ones. They are easier to assemble, more durable and stronger.

All metal scaffolding has the same shape - vertical posts connected by crossbars and slopes. The only difference is the way the parts are attached to each other:

Pin scaffolding. They are called so because the crossbars and posts are connected using pins. Pieces of pipe or perforated disks are welded on the racks, and bent pins are on the crossbars. This system is very easy to assemble and can withstand heavy loads. Pin scaffolding for buildings of simple shape is very easy to implement; going around bay windows and projections is much more difficult. The principle of connecting pin scaffolds Clamps. For racks and crossbars, round pipes are used, which are fastened together using specially designed clamps. The system turns out to be very mobile and movable; you can easily get around any curved facades. The downside is the limited load capacity and height (according to GOST - no higher than 40 meters). Clamp scaffolding - quick installation/dismantling Frame scaffolding. Frames of the same size are welded from a round or rectangular pipe. They are connected to each other by transverse pipes and jibs. They have a modular structure and can be easily expanded both in height and in length. They have a certain step in length - 1.5/2/2.5/3 meters, in height one section is usually 2 meters, the standard depth is 1 m. Some frames have wheels for easier movement on a flat surface. Connection of flag-type elements - pins with a slot into which the flag is inserted are welded on the frame. Holes are made in the crossbars and slopes. The elements are put on a pin and secured with a flag. Sections are built up using connecting pipes of smaller diameter welded to the frame posts on one side

With this method, it is important to have perfectly selected pipe sizes so that there is no backlash. Frame scaffolding - the principle of fastening the crossbars and wedges. Although generally similar, the designs differ in the form of the connection

On the jays with a certain pitch (usually 2 meters), perforated discs are welded. Special cleft-mouth type locks are welded onto the jumpers at both ends. The locks are fixed to the disk using a specially shaped wedge. Such scaffolding connects and disconnects quickly, has high mobility, and can be used on facades of complex shapes. Wedge scaffolding racks and crossbars are connected using wedges and specially shaped locks

When making metal scaffolding yourself, pin scaffolding is most often used. They are the easiest to implement, however, they are only good on rectangular facades; to bypass more complex shapes, you have to weld additional tubes.

Technology for assembling dismountable construction trestles

In order to assemble the structure, you can also use nails - this is the cheapest and most practical option. However, some elements will not hold well after such fixation, and the scaffolding will turn out to be unreliable. The best and fastest way to assemble trestles is with the help of special screws and a screwdriver.

Disposable sawhorses are most often fastened with nails Source ireland.apollo.com

Work area

Actually, that’s why we assemble construction trestles with our own hands - a platform. Depending on the nature of the work performed, the size of the site is also selected individually. The weight that it must withstand must be no less than the weight of a person plus the load from tools and materials. In a word, 150-170 kg will be quite enough for any construction and repair work. The overall dimensions of the platform should be such that it fits into the doorways, which is no more than 70 cm, and its length should not exceed one and a half meters, otherwise it will be inconvenient to maneuver.

Consequently, to make two sawhorses, a platform and, possibly, a wall stepladder, you will need no more than 12-15 meters of edged board, and this is quite a bit to guarantee a convenient eight-legged assistant for any repair and construction.

Self-tapping screws and nails

Doubts about the choice of fasteners are quite understandable. Nails are easy to drive and provide strength to scaffolding because they have some flexibility to absorb the load. The inconvenience is that the building structure is almost impossible to disassemble without damaging the wood.

Self-tapping screws are convenient in this regard; they can be unscrewed without damaging wooden surfaces, but they are characterized by great fragility. Black self-tapping screws made of hardened steel alloys can break when hit or simply under weight.

Note! Anodized self-tapping fasteners are somewhat stronger; they can be distinguished from ordinary ones by the greenish tint of the coating.

If the owner often works on the site with his own hands and the wood is needed in its most complete form, you can use anodized screws, and to be sure, hammer in only two or three nails at the junctions of the scaffolding, just in case, for insurance.

Nothing extra: mobile trash can

Forgive me for such a natural comparison, but do you know why the horses that drove chaises around the city had a bag tied under their tails? Yes, precisely for this reason, to keep the pavement clean. So my working goat got such a device.

I cut the rim off the paint bucket and cut off the lid. You can attach a garbage bag between the rim and the lid. And the rim itself was fixed with a movable holder. I hope you liked my construction beast. I will be glad if my experience helps someone with repairs

Thank you, Olga! A charming master class from a real craftswoman! It's nice to look at your work. We don't even have anything to add. The only thing you can do is to suggest complicating the task, as in this short video on creating a multifunctional carpentry table:

Watch this video on YouTube

We are waiting for your impressions and comments, as well as new materials in the section “This is not a woman’s business!”

PHOTO: Olga Yarovaya

Complete assembly of goats: what material is required

In order for the trestles to be foldable, each of them will require two door canopies, which will connect the elements. To complete this work, you need to lay the squares one next to the other on any flat surface. They should be located in one line at the ends. If there is no suitable workbench, then all the work can be done on the floor.

At first glance, it may seem that the structure made from scraps of plywood looks flimsy, but this impression is deceptive. After complete assembly, the strength will be at a very high level.

PHOTO: YouTube.comThe elements are located as needed, it’s time to connect them together

Door awning fastening

The canopies are attached to the same self-tapping screws with a slight indentation from the edge of the elements, but without going beyond the joint of the plywood scraps. It is better to purchase canopies with three or even four holes for fixing screws. This will give the structure additional strength.

It is best to use hardened black self-tapping screws (they are also called German, or Germanic). The main thing is to choose the right length so that they can sink into the wood to a depth sufficient for fixation (through both layers), but at the same time do not stick out too much from the back side. Otherwise there is a risk of injury.

PHOTO: YouTube.com Trying on door canopies before final fixation

The final touch in the manufacture of construction sawhorses

Despite the fact that after fastening the canopies, the sawhorses seem ready, they lack stability. If you press from above, the legs will simply move apart in different directions. This means a little modification is needed.

To prevent falls from the scaffolding, it is necessary to install a limiter that will hold the legs in the desired position. A wide and durable canvas belt is ideal for this. Having measured the required length (the same for both trestles), it needs to be fixed on the lower jumpers of the elements. However, simply screwed in screws will not work here. The connection needs to be strengthened. This can be done using a metal profile through which the screws will be screwed.

PHOTO: YouTube.com The canvas belt will perfectly hold the sawhorses in the desired position

Varieties

How to make sawhorses for firewood?

Thanks to modern capabilities and technologies, you can buy various types of scaffolding in stores. These structures can have different sizes, assembly methods, production materials, and can also be equipped with various additions. The first type is considered to be ordinary construction scaffolding. They are produced similar to stools, but using more advanced technology. This type of structure is classified as foldable, as it can be disassembled into individual elements. In this case, the largest part is considered to be the working flooring.

Modern versions of construction trestles have decking that can be installed at different heights. This became possible thanks to the features of the sidewalls, which look like stairs. Typically, these devices weigh a lot, since they are designed for the work of several people at the same time. The dimensions of this design are considerable. A professional construction trestle has the following dimensions: 150 (200) cm – width and 180 cm – height. This design option is ideal for working on large objects, but for an apartment it is considered quite cumbersome. Often the construction trestle package includes a ladder, a limiter, and wheels with stoppers.

The second type is a transformer. This is an ideal tool for indoor work and is quite compact when assembled. The main characteristics of this type of construction trestle include light weight, practicality, ease of use and transportation. Due to the design features, this option can be used not only on a perfectly flat surface, but also when inclined and even on steps. Such scaffolding is often used as an alternative to stairs.

The transforming scaffolds have a height of no more than 100 cm, a width of 50 cm. When unfolded, the dimensions are no more than 160 cm, and when folded, the goat can easily fit into a car trunk. Based on the material used, construction trestles are divided into aluminum, wooden and combined. You can also find painting scaffolds with dimensions of 50 by 100 cm on sale.

Storage and use of sawhorses

Using our recommendations on how to make a sawhorse, you will create a stable structure, and cutting firewood on it will be a pleasure. You can also view ready-made sketches, photo and video materials on the Internet.

Equally important is the correct use of sawhorses. You should not load too massive and heavy logs on it.

The folding design of the sawhorses is suitable for cutting firewood using a hand saw or chainsaw. This device is simply indispensable in the homestead for collecting firewood and stove logs to light the stove, barbecue or fireplace in the house.

Drawings for manufacturing

Schematic drawing

Dimensions of trestles

• height 811 mm;
• width of the upper base 844 mm;
• minimum width (legs) 711 mm.

Goat drawings in Sketchup

In case you want to change the design and dimensions at your discretion, you can download the file for editing in SketchUp

Download file: scetchup.zip [39.73 Kb] (downloads: 995).zip

3 Metal sawhorses for cutting wood

Metal products are compact in size, have a long service life, and are highly reliable. Small specimens intended for processing small volumes of wood, and larger machines for large-scale production are made from this material. The cost of a homemade model using scrap metal waste is low. To make them at home, you need to prepare the following materials and tools:

• profile corner 50x50 mm, pipe of similar characteristics;
• grinder, hacksaw;
• measuring tape;
• chalk;
• connecting bolts, welding machine.

A sketch is drawn up listing the main elements and the mandatory marking of each of them. The design of the upcoming product may be different, but in order to give greater durability, two additional profile elements at an angle or a transverse beam of the base are additionally installed. For example, from a piece of pipe. In the second case, it is necessary to protect the saw teeth from contact with the beam, so at the final stage of assembly, a piece of timber is secured on top.

The fastening points are marked by welding or bolts. If a bolted connection is provided, then additionally indicate the location of the holes. A system assembled by welding is one-piece; a dismountable system is more mobile.

All parts are cut according to the intended dimensions using welding or a grinder. To prevent sliding and turning of the logs while sawing, a jagged edge is prepared on the inner side of the outer legs. For the safety of further work, the cut sites are processed, removing scale, burrs, and other defects from each edge. The product is being assembled. To protect against rust, non-demountable structures are treated with an anti-corrosion compound.

You can build a mobile version of folding trestles from metal. The simpler the design, the less often the device breaks down, so this type of machine is manufactured as simply as possible. When folded, it takes up little space, is convenient to store and transport, but more manufacturing and assembly costs are required.

The main difference is the mobility of the X-shaped support; it can be folded like scissors. The bolts are not fully tightened, to prevent them from unscrewing spontaneously, an additional lock nut is installed. Installing a limiter helps fix the supports in the desired position. This can be a metal chain attached to one leg of the support, and a hook is made on the other to hook it.

Goats for working with a hand saw

Most often, a regular saw is used for harvesting wood; this allows you to cut small-sized logs. Goats for such purposes may have standard dimensions. To assemble such a structure you will need the following materials:

• Beam with a section of 100 by 100 mm. This thickness of wood is enough to create a stable structure. The length of the material is taken from 1 to 1.5 meters.
• Beam for legs of smaller diameter. For supports, material from 50 to 50 m in cross section and a meter in length is suitable. The goat will have 4 legs in total.
• Material for crosses. The “horns” of the structure are made of 10 by 10 cm timber. Some structures require reinforced legs. For them, timber with a cross section of 30 by 30 mm or more is used. For stability you will need 4 supports, but you can leave only two.
• Fasteners. It is best to use self-tapping screws to connect parts. The diameter of the cap is 45 mm and the length is 100 mm. The entire product will require about 40 fasteners.
• Coating. In order for the timber to remain intact for a long time, it must be impregnated with varnish or other protective compound.

The material will be required for homeowners who do not have building materials on the site. Those who have scraps of timber or pipes left over from other work can use them in assembling the trestle.

To create the design you will need the following set of tools:

• hacksaw for cutting timber;
• corner for aligning parts of the structure;
• pencil for marking;
• hammer or screwdriver;
• roulette;
• finishing coat and brush.

Once the material has been purchased, assembly can begin. The goat frame is made starting with wood processing. To do this, use a tape measure and a pencil to mark the cutting areas. They need to be made 6 on each side. There will be 12 of all grooves for connecting the legs and crosses. With a beam cross-section of 100 mm, the depth of the groove is 25 mm, this is enough for a strong fastening. When cutting the grooves, make sure that they are a couple of millimeters smaller than the legs. After marking and making grooves, all parts are assembled into a single structure.

After assembly, fastener reinforcements are installed; they enhance the strength of the structure and make work safer. To do this, saw off the bottom of each leg so that there is enough space to install a new fastener. After assembling the product, it is treated with a protective compound. To do this, use varnish or stain. When the structure is dry, it can be used.

Mobile trestles made of wood

The design of conventional trestles has rather large dimensions and weight, which is a serious obstacle when transporting the machine. But you can also make a mobile installation with your own hands, which will be foldable and can be easily carried. But, as a rule, such plans require more costs and time to assemble.

For folding trestles you will need the following material:

• durable, but small in diameter wooden beams. You will need at least 4 units of them;
• for the base of this structure it is best to use a metal pipe with a length of 1 to 3 meters;
• since the design is folding, you will need a limiter (you can use a strong rope, a small chain, a good belt or cable);
• To connect the components you will need a wood drill. It is worth choosing the most durable option.

To avoid unnecessary costs and reduce the likelihood of device breakdown, this machine is manufactured as simply as possible. You need to start the assembly with the beams. You can make them yourself from a 50 mm board. After receiving the finished material, it is necessary to mark the location of the cut where the legs for the trestle will subsequently be installed.

After drilling a hole on each strip for the pipe, the base is inserted into them, and the legs are set in their places. Next you need to make a limiter for the racks, which will not allow the legs to move apart.

Mobile wooden sawhorses for sawing firewood

Here you should be careful, choose the same length for both sides, which will allow the sawhorses to open 350 to 450 degrees. Thus, a structure will be assembled that will be easy to fold and store in small spaces.

Start of work: preparation of material

It is more convenient to cut the plywood on a circular saw. If you don’t have one at hand, you can use a hand saw, but in this case the work will be very labor-intensive and time-consuming. A regular electric jigsaw with a suitable blade can also help here.

PHOTO: YouTube.com Plywood scraps are unraveled to the specified size

Dissolving scraps to the desired width

After the plywood scraps are cut to the required length, you need to cut them to width. After all, too wide elements are completely useless here. It's just extra weight. As for strength, when the trestles are assembled, they will be able to withstand more than 100 kg each.

Particular attention should be paid to safety precautions when working with a circular saw. Do not bring your hands too close to the rotating disk

If you need to push the part, it is best to use any piece of board or stick.

PHOTO: YouTube.com When the parts are adjusted to the desired width, you can begin assembly

Leg assembly and fitting

The performance of the device depends on the quality of the marking of the hole for the bolt. Therefore, preliminary fitting using technology is necessary:

• the leg is placed on the table so that the cutout hangs over the tabletop (you can use a stool, chair)
• the support bar (upper) is installed vertically in the groove
• a second leg is added on top of the first (the bar should fit snugly into the cutouts in both parts)
• the structure is temporarily tightened with a clamp

Then the following operations are performed:

• Using a vertical square, the intersection of the legs is transferred to the side surface on both sides of the structure
• the resulting points are connected by a line, which becomes the vertical axis of rotation
• the longitudinal axis of the leg is marked with a square
• at the intersection of these lines there will be a center for the hole of the M10 bolt, which is the hinge of the connection

Attention: The holes must be perpendicular to the plane of the boards, so a jig is required. They can serve as a cut in a block pressed to the leg with a self-tapping screw or clamp

If the hole is inclined, the legs will not be able to transform into the working position.

The legs are assembled in stages:

• the bolt goes through one piece
• two washers are put on it to facilitate the rotation of the wooden elements relative to each other
• the second leg is put on the threaded part
• the hinge joint is secured with a nut

The result is a set of two legs, into the cuts of which a support bar is easily inserted from above.

Design and use cases

Unlike classic trestles, universal trestles are folding, which makes storage and transportation easier. The design of the carpentry and construction device is as follows:

• legs with spacers, hingedly connected to each other
• removable support bar
• belt tie at the bottom

The device allows you to harvest firewood, cut long lumber and support scaffolding panels (you will need 2 pairs of trestles) by default. A wooden table top can be attached to the support crossbar to accommodate power tools (for example, a cross-cut machine, a drilling machine, a sharpening machine).

If you assemble a lightweight frame from boards or plywood, you can build a large-sized carpentry table-workbench from two trestles for assembling furniture.

Cutouts in the support strip allow you to work with tubular workpieces and press the lamellas of the joinery parts being glued together. On one side of the trestles you can attach a sheet of plywood, gypsum board, OSB for marking, straight or figured cut.

Assemble the frames

1. To make half-wood joints, install a 19 mm thick groove disk into the saw machine and make test joints on scraps with a cross-section of 19 × 114 mm, setting the sawing depth equal to half the thickness of the workpiece. Cut cutouts in legs A and crossbars B for half-tree joints (Fig. 1 and 2).

2. Glue the A/B leg frames together and secure them with clamps. When installing clamps at half-wood joints, in order to evenly distribute the pressure over the entire gluing area, place wooden scraps under the jaws of the clamps. Check the squareness of the assembled frames.

3. Create a 15° bevel on the top edge of each A/B frame (Photo A).

Set up a circular saw to cut the bevels at 15°, attach a flat board to the A/B leg frame, and cut a bevel on the top edge of the frame.

Assembly diagram

1. Place two more boards in the shape of a rectangle on the inverted structure and connect them. It turns out to be flooring or an area for work.
2. Take four more wooden panels with dimensions 1100x100x30 and attach them at the ends. The result is a structure somewhat reminiscent of a table.
3. The next step is to strengthen the structure with boards 1700x100x30mm and 1500x50x30mm. They must be attached so that the opposite reinforcements are in different diagonals.
4. And the last point is attaching the ladder. For more convenient operation, the steps at the bottom can be made with a small protrusion. You select the length of the stairs based on individual preferences.
5. That's it, your goats are ready. But for safe construction and repair work they need to be checked. To do this, we place any objects with a large weight on the surface; if the trestles can withstand it, then you can not be afraid and safely use them in installation.

Wooden scaffolding, otherwise known as trestles, for repairs.

Wooden scaffolding, otherwise known as trestles, for repairs.
If the theater begins with a hanger, then renovation of the premises always begins with the assembly of wooden scaffolding or, as they are also colloquially called, trestles. The reliability of the “goats” determines how safely and quickly you will carry out all the apartment renovation work, as well as the speed of finishing work.

Additionally, of course, you will need a hanger, a wall ladder and a dining table.

In this article I will tell you and show in photographs how and with what tool you need to assemble the “goats” and how much material is needed for this.

When I use the word “goat” in the article, you know that this is a table for temporary use during repairs. It is done by builders and finishers to gain access to the top of the walls or ceiling for repair work. That's why I won't put quotation marks.

For the goat, the material selected is completely dry and light. And, of course, not very expensive. Remember that it will need to be moved frequently and transferred from one place to another.

You also take your choice of instrument. If you are going to twist the parts of the goat with self-tapping screws, then you need a screwdriver, but it is better to have a drill with an attachment (a bit for wood screws).

If you use nails to join parts together, which I certainly don't recommend when assembling sawhorses, then you will need a hammer. To cut wooden parts you need a hacksaw or an electric jigsaw. But I always use a hand-held circular saw.

Well, to mark our future parts of the goat we need a pencil with a tape measure and a square.

The material I always choose is edged pine boards and 55-60 mm wood screws.

To assemble two trestles, we will need 3-meter boards 150 mm wide and 30 mm thick.

The height of the trestles is easy to determine: you need to take a tape measure and measure the distance from the ceiling to the head of the working person and subtract approximately 150-200 mm from this distance.

Well, that is, with an average ceiling height in apartments (2.6 m), the trestle is made approximately 0.9 m high.

So, the first thing we need to do is the main sites of our future goats, where all the work will be carried out. These areas must have enough space for the person who will be working on the sawhorse. You also need a place for a basin with a solution, which weighs approximately 40-50 kg. Accordingly, the platform must be strong and stable; our future goat must withstand a load of at least 150 kg.

In this matter, we always need to take into account the width of the main light doorways, so that we can move our future goat to any room of our apartment. Since light doorways without installed doors are never less than 700 mm, the platform for the trestles must be made 600 mm. The exception is the bathroom premises, where with a door installed with a door leaf width of 600 mm, a goat will not fit through.

But it won’t be needed there, since all types of work at heights - plastering the walls, laying tiles on the floor and walls, installing the ceiling, as well as grouting the tile joints will have already been completed, and after installing the door there will be nothing left to do with the trestles . Repair and Construction Do-it-yourself ladder Read more

We will need only 16 meters of the main whole boards for making shields for a pair of trestles and a shield for a table, that is, 5 whole 3-meter boards and another 1 m of board. We cut all other boards to length with a hand-held circular saw into two halves.

For the main sawhorse boards we take our first four whole 3m boards. Use a tape measure to find the middle of the board and cut them in half. This way we will have the base ready: two main platforms for the trestles, 600 mm wide and 1500 mm long.

Then we need to cut our remaining boards with a hand-held circular saw. From these narrow boards, 30 mm x 75 mm in size and 3000 mm long, obtained during the cutting process, we will make the remaining parts (blanks) for our goat. This is done so that the goat is not so heavy and can be moved by one person.

We saw off 4 blanks of 600 mm each and fasten our four separate boards into a shield.

We screw the crossbars that hold the boards together into a shield with self-tapping screws at a distance of 150 mm from the edge of the boards. We fasten each board with 4 self-tapping screws.

Now we need to make the following: 8 blanks 900 mm long for four pairs of legs of two goats, 4 blanks 650 mm each for the lower steps and 4 blanks 550 mm each for the upper steps.

Let's start assembling our future legs. To do this, we turn the shield over and, laying out our blanks for legs and steps on it, fasten them with self-tapping screws.

The upper part of the goat's legs, which will be attached to the shield, need to be narrowed slightly inside the shield (20-30 mm on each side), and the lower ends of the legs, on the contrary, should be spread 30-40 mm larger than the width of the shield, so that our future goat will be stable on the floor, and then screw our steps onto them. Like this:

In order for all the legs of the goat to be the same, they must be assembled by stacking them on top of each other.

Next, when everything is ready, we proceed to assembling the goat itself: we screw the goat’s legs from the inside to the shield with self-tapping screws, turn our goat over and align it with two 1850 mm long jib bars that we previously prepared, diagonally to the structure. So that they are screwed in relation to the sides of the goat “crosswise”. This is also done for the stability of the structure.

When screwing on the jibs, we also move the bottom of the steps a little to the side and secure them with self-tapping screws.

We complete the bottom frame of the structure in a circular manner with two crossbars of 1600 mm each, and the goat is ready. We twist the entire structure with self-tapping screws so that there are 2 of them per connection. Now you can safely, without fear, start working with it.

Additional information: if the repair is carried out in a room with finished floors, then you need to screw, for example, pieces of linoleum onto the bottom of the legs of the goat so as not to scratch the floors.

(Don’t forget about the obligatory lunch, otherwise, where will the energy come from for work?)

So, we still need to make a table out of the boards so that we can have a proper lunch or just drink tea.

And, of course, a clothes hanger. In addition, you need to purchase plastic film to cover clean clothes.

The “furniture” set to start the renovation is ready!

For rooms with ceiling heights of up to 3.5 meters or more, the trestle is made separately. But this depends on the individuality of the apartment and the layout.

Drawing of construction trestles. DIY installation

When carrying out any work related to repairs or maintenance of the house, it is required to rise to a certain height. If you can screw in a light bulb with a chair, and cover a small crack with a stepladder, then extensive work requires greater mobility.

To move at height, construction trestles, otherwise called scaffolds, are created. Ready-made structures are available in construction stores, but prices run into thousands of rubles. It’s easier to make them yourself, and it costs several times less.

Construction trestle structure

Before you start making construction trestles with your own hands, we select materials for production. There are three main materials from which goats are made:

• metal;
• tree;
• wood-metal combination.

Since metal ones are difficult to create and quite expensive in terms of materials, let’s consider wooden trestles.

After choosing a material, it is worth understanding the conditions of their use. If these are stationary or rarely moved scaffolds, then it is worth creating a disposable scaffold. If you plan to move the trestles frequently, we choose folding trestles.

Before starting carpentry work, we create a drawing and calculate the required height. The standard height for comfortable work for an adult man is 80–90 cm.

For a finished product with a height of 85 cm, legs 95 cm long are needed.

The length must be chosen such that when a construction site board is placed on top, the beam protrudes at least 5–7 cm on each side, but it is better to take it with a margin.

The design is extremely simple, when open it resembles the letter “A”, and can be used both at a low height and with the help of two trestles at full height.

Preparation

After creating the drawing, you need to decide how long the platform will be, and how many trestles will have to be made for it. Goats are always created from two or more - if the board being applied is long and can break in the middle.

Collapsible wooden construction trestles

The advantage of collapsible trestles over a conventional platform is their reusability and the ability to quickly remove them from storage and use. In conventional scaffold construction, only boards fastened with nails are used.

After completion of work, it is difficult to leave them for storage unassembled. To ensure that such scaffolds do not take up much space, they have to be dismantled, which is difficult if they are made with high quality.

Collapsible trestles do not take up much space; they can be transported and used for various needs other than their intended purpose. To create a sawhorse, you need two supports.

To make one support you will need:

• four boards for legs - 0.95 m;
• board 0.9 m for the top;
• three crossbars of 0.85, 0.77, 0.7 m each.

Carpentry work

The goats are assembled in accordance with the recommended instructions.

1. Make markings on the legs, cut off excess wood on both sides at an angle of 800. The cuts should be parallel.
2. Use the finished leg as an example and make the rest.
3. Check that the ends of the top board, which will support the platform, are at an angle of 900.
4. On the boards of future spacers, measure an angle of 800 at one end and 1000 at the other. Cut.

5. The blanks are ready, now the space for the top board is cut. To do this, fold the two finished legs into the position that they will take when open, draw an angle of 900, and cut. All the others cut through this leg.
6. The legs are connected like scissors, a rotation axis is drilled into them, in which the bolts are not fully tightened, allowing the legs to open and close.
7. All that remains is to make spacers between the finished legs, two on the wide side and one on the narrow side. Then fasten the tension belt to the lower spacers.
8. One support of the future construction site is ready, the second one is being assembled according to the same scheme.

Collapsible trestles are an easy and inexpensive way to create a construction site that is durable, mobile, and able to support the weight of an adult man, as well as building materials.

Images from www.forumhouse.ru were used for this material.

How to do it yourself?

The most practical and inexpensive option for a construction trestle, which can be made with your own hands, is a folding wooden one. It takes up minimal space and can also be used when working in a country house or apartment. The first thing you should decide on is the height of the legs, it is equal to the height of a person minus 10-12 cm. You can arbitrarily determine the number of spacers and the beam section.

The upper ends of the frame can be connected using door-type hinges. To fix the legs, you should think about a limiter. A couple of pieces of rafter tape are taken and then fixed to the spacers below. The distance should be such as to maintain the stability of the structure. To fix the elements to each other, you can take nails and then bend them on the back side. But in order for the device to be practical and reliable, it is worth using self-tapping screws.

The next step is to prepare the site, the dimensions of which should be selected according to your preferences. It should be able to withstand from 150 to 170 kilograms, and its dimensions should be selected in such a way that the device easily fits into the doorway. The approximate width of the site should be 0.7 meters. To acquire a high-quality construction sawhorse, you will need to prepare no more than 150 centimeters of edged board.

Detailed assembly instructions.

• Markings are made on the legs, and excess wood is cut at an angle on both sides. At the same time, do not forget about the parallelism of the cuts.
• Using one leg as an example, it’s worth making the rest.
• A check is made to ensure that the upper ends are at an angle of 90 degrees.
• Future spacers are marked with angles of 80 degrees at one end and 100 degrees at the other.
• After preparing the blanks, it is worth cutting a place on them for the top board.
• The legs must be connected in the form of scissors, after which the rotation axes must be drilled into them. In the latter case, it is worth not tightening the bolts completely so that the legs can open and close.
• Spacers are made between the prepared legs. You should get two spacers on the wide side, one on the narrow side. A tie belt must be attached to them on the bottom side.
• Once one support is ready, you can begin assembling the second.

Many construction and renovation jobs involve heights, as the worker constantly has to reach. A ladder and a stepladder limit your freedom of action, but a construction sawhorse is a completely different matter.

You can see how to make construction trestles with your own hands in the following video.

Other goat options

The most widely used for sawing single thick logs with chain saws are various sawhorse designs with fixation of the rear part of the log.

These are the ones that are produced most industrially, besides the cruciform ones.

Their designs are so simple that they do not need detailed descriptions; everything can be seen in the photo. Such sawhorses for sawing firewood can be made by any home craftsman who is more or less able to hold a tool in his hands. The main thing here is the ability to balance the dimensions of the support platform with the size and weight of the logs being cut. It may not have a rectangular shape, or even be completely replaced by stops. I liked this goat design for its simplicity and minimalism.

Or this option, designed for very thick, but not long logs:

And finally, we will present a wooden structure that is very successful for home production, which is also guaranteed to ensure that the saw does not jam due to the small width between the saw stops at the cutting site.

In such sawhorses, the log is laid with equal overhang on the sides for stability, and is sawn in the middle. Next, do the same with the resulting pieces.

In all cases, when making a trestle yourself, you choose the height individually, so that, first of all, it is convenient for you.

Dear readers, if you have any questions, please ask them using the form below. We will be glad to communicate with you;)

Do-it-yourself sawhorses for cutting wood? Easily! Good owners make sure in advance that they have enough firewood in stock for the winter. To prepare them, you must have an indispensable tool for all owners of private houses - a sawhorse for sawing firewood.

This is a fairly simple design that everyone should have in their dacha to make it convenient to process, prepare firewood and saw metal strips or wooden boards with millimeter precision.

Making goats with your own hands is quite simple, and even someone who does not have any special skills can handle it.

Kinds

To make a classic version of such cutting equipment, you will need any of the following materials:

Despite the fact that the design itself is simple, sawing sawhorses can be classified as machines. For this reason, during production, certain conventions must be observed, one of which is the presence of a drawing or plan according to which the assembly will be carried out. When planning, it is worth signing all the dimensions; this also applies to even the smallest details.

Criterias of choice

The main thing to pay attention to when assembling is the dimensions. This will be affected by:. All the time spent on work will depend on what sizes are chosen.

The best option is to make the machine with a height of 0.9 to 1.1 m. Thus, the person who will work will not bend his back too much, and his arms will be positioned horizontally. It will be easy to work and the load on your back will be reduced

All the time spent on work will depend on what sizes are chosen. The best option is to make the machine with a height of 0.9 to 1.1 m. Thus, the person who will work will not bend his back too much, and his arms will be positioned horizontally. It will be easy to work and the strain on your back will be reduced.

Features of using tools when working on sawhorses

If you plan to process wood with a regular two-handed saw, then you will definitely need a reliable support for the second one. For this reason, when planning, take care of the presence of such elements. An affordable option is to create a support from timber, which will give you the advantage of installing a support anywhere. When using a power tool like a chainsaw, make sure there is a sturdy surface on the sawhorse.

Goats for sawing firewood with a chainsaw have their own characteristics, since there are differences in operating rules that affect the safety of the worker. In this case, you will need to take care in advance of a place for free hanging of the material that will be sawn. This way you can avoid the tool getting caught in the sawn blade.

How to do it yourself

To make a bed from timber, you need to familiarize yourself with the stages of the process, develop detailed drawings of the future product, purchase material and accessories. To work, you will need a standard set of tools and consumables.

Before making a bed, the dimensions of the location are taken, the dimensions of the bed are calculated according to the size of the mattress and the number of people who will use it, their height.

Materials and tools

First you need to purchase solid wood. At the same time, you need to monitor the quality of raw materials. The boards must be completely dry and free of bends and cracks. Boards needed:

1. for making a frame 25x200x2400 mm - 4 pcs.;
2. for support beams 50x100x2400 mm – 3 pcs.;
3. for decorative finishing 25x50x2400 mm – 3 pcs.;

For the legs, it is recommended to purchase timber 100 by 100 and 2400 mm.

To create a slatted base you need to buy 19 planks 25x75x2400 mm.

In addition to lumber, you will need 3, 5 and 6 cm screws and metal corners. If solid oak is used, it is better to use ordinary nails for fastening.

To implement the plan you will need the following tool:

• tape measure, ruler, building level, square;
• circular or hand saw, electric jigsaw;
• drill or screwdriver;
• grinding machine, sandpaper;
• clamps;
• glue and putty for wood;
• varnish, stain, brushes and rollers.

Frame making

If the bed is planned to be made with legs, the production of a piece of furniture begins with their blanks. To do this, pieces of the required length are cut from 10x10 cm timber. At a height that corresponds to the size of the bed, metal corners are screwed on.

Then 2 pieces are cut from the 5x10 cm beams, the length of which is equal to the dimensions of the mattress. To calculate two more frame boards, subtract 10 cm from the width of the mattress. Then the blanks are placed in the right place and tightly secured to the corners, which are already screwed to the future legs.

The final stage of creating the frame is the installation of transverse boards, which will serve as a shock-absorbing base for the mattress, in increments of 5 cm.

Slats and back

Instead of a slatted base, you can make a base from lamellas, which are more flexible and can withstand heavy weight.

First, special supporting beams with a thickness of at least 4x4 cm are attached to the inside of the side boards of the frame using self-tapping screws in increments of 15 cm. The grooves in which the lamellas will be placed are first cut out in the timber, but this step can be dispensed with. Then all that remains is to screw the elements - and the frame is completely ready.

To simplify the manufacture of the headboard and footboard, a chipboard or MDF board is used, from which the header of the required shapes and sizes is cut out with a jigsaw, the edges are sanded and covered with veneer. If possible, it is advisable to make the backrest from wood, using various processing and finishing methods.

Finishing

Giving the finished product an aesthetic appearance is done by treating its surfaces, painting (staining) and opening with varnish. Even if the wood has undergone primary processing in advance, this is not enough to make the bed look beautiful and well-groomed.

Immediately after the frame and its components are ready, all elements are carefully polished with an electric machine and discs. First with a large coating, then with the finest. Finally, polishing is done with a felt disc.

Further finishing depends entirely on the choice of the owners: color, texture, matte or glossy surface, the presence of additional decorative details. All this is used in accordance with the original design.

Leg assembly and fitting

The performance of the device depends on the quality of the marking of the hole for the bolt. Therefore, preliminary fitting using technology is necessary:

• the leg is placed on the table so that the cutout hangs over the tabletop (you can use a stool, chair)
• the support bar (upper) is installed vertically in the groove
• a second leg is added on top of the first (the bar should fit snugly into the cutouts in both parts)
• the structure is temporarily tightened with a clamp

Then the following operations are performed:

• Using a vertical square, the intersection of the legs is transferred to the side surface on both sides of the structure
• the resulting points are connected by a line, which becomes the vertical axis of rotation
• the longitudinal axis of the leg is marked with a square
• at the intersection of these lines there will be a center for the hole of the M10 bolt, which is the hinge of the connection

Attention: The holes must be perpendicular to the plane of the boards, so a jig is required. They can serve as a cut in a block pressed to the leg with a self-tapping screw or clamp

If the hole is inclined, the legs will not be able to transform into the working position.

The legs are assembled in stages:

• the bolt goes through one piece
• two washers are put on it to facilitate the rotation of the wooden elements relative to each other
• the second leg is put on the threaded part
• the hinge joint is secured with a nut

The result is a set of two legs, into the cuts of which a support bar is easily inserted from above.

Lower tension strap

The support bar prevents the legs from folding inward. However, a home craftsman can accidentally move them outward, causing the structure to “corrode” and lose its rigidity. To do this, a belt tie is used to secure the opposite lower struts. It is installed using the following technology:

• trestles fold out
• the middle of the lower strut is marked
• a through hole is drilled with a 10 mm drill (for an M10 bolt)
• a hole is punched 40 cm from the belt carabiner into which the bolt is inserted

After that, it is enough to secure the bolt with the belt in one spacer with a nut, tighten the belt around the opposite spacer, and cut off the excess length. The same strap secures the support bar to the legs during transportation or storage when folded.

Thus, universal folding trestles can be made on your own with a minimum set of tools within a couple of hours. All parts are ready-made templates, which facilitates the further assembly of the required number of these transformable devices.

Features of manufacturing wooden scaffolding

If you decide to make trestles from wood, then the step between the racks can be equal to the limit of 2 to 2.5 meters. As for the width of the flooring, it should be equivalent to one meter. You should not make the structure too high; the maximum height limit is 6 meters. To carry out the work, it is necessary to prepare boards 50 millimeters thick. As for their width, this figure should not appear less than 100 millimeters. You can replace such blanks with a square beam of 10 cm. The racks and stops can be based on round timber. Spacers and barriers are typically made from boards that are 30 millimeters or more thick.

Briefly about the main thing

The main advantage of homemade trestles is their low cost and the ability to assemble a structure of exactly the height that the builder needs. If desired, the trestles can be modified at any time - for example, reducing the height, slightly filing the legs, or even adding a second tier. To reduce the cost, instead of wood, in some cases you can use plastic or remnants from profile pipes. To work, you will need a beam of the required size, a screwdriver and self-tapping screws, a jigsaw or saw. The work takes 2-3 hours.

Choosing a place to build

When choosing a place to build a goat house, give preference to a small hill or plain. In the lowlands, the barn will be damp, which means the animals will constantly get sick and waste away.

Before construction, the area for construction must be cleared of vegetation: remove trees and shrubs with maximum uprooting of the root system. After preparatory work, level the area.

Keep in mind that each adult goat needs about 1 square meter. m. area, and for kids - 0.6-0.8 square meters. m. Place the building on site so that the façade and walking pen are located on the south side.