✅ How to reduce vibration of a washing machine on a wooden floor -

Articles

All photos from the article

Vibration of a washing machine on a wooden floor can not only lead to destruction of the base, but also cause damage to the device itself. This is why experts recommend approaching this task very responsibly: even seemingly durable boards may not withstand the impact of a loaded drum rotating at high speed.

However, even if you need to mark the device specifically on a wooden floor, this can be done with relatively little labor.

The structure must be level and solid

How to install a washing machine on a wooden floor

The narrow Eurosoba washing machine has a powerful engine, excellent drum performance, and all the latest functionality.
But there may be problems with installation on a wooden floor.

This brand is distinguished by the presence of comfortable legs located around the perimeter of the machine, made of high-quality material that meets the requirements of world standards. This fact allows you to place the washing machine in any convenient place. The easiest way to install the unit is on a concrete floor.

Article on the topic: Is it possible to make a suspended ceiling in a kitchen with a gas stove?

A different situation arises with wooden floors. Installing it somehow will not work - this will lead to strong vibration of the machine during washing, which will cause harm not only to household appliances, but also to the floor.

Troubleshooting yourself

To eliminate some malfunctions, it is not necessary to take the device to a service center; you can do everything yourself. To do this, you need to do the following:

If foreign objects get behind the drum, you need to bend the rubber seal of the hatch on the front panel, fixing the drum. After this, you should hook the item and pull it out. If you can’t do this, the only thing that will help is removing the heating element and disassembling the automatic machine, which is best left to a professional.
If the laundry is unevenly distributed, you need to perform an emergency drain of water and unlock the hatch. Next, you should take out the laundry, separate them from each other and carefully place them in the drum. If overload is observed, then remove some of the things from the machine.
If there is a problem with installation, you need to determine the correct height using a level and adjust the legs of the washer. You can also level the floor or lay down a sheet of chipboard, fiberboard, or anti-vibration pads. Using a rubberized mat will also help if the device slides on the surface.
If there are transport bolts, you need to turn the machine with the back wall towards you and unscrew 3 or 4 fasteners with a wrench or pliers. In some cases, there are more fasteners, and they are located under the top cover, so it is better to check the instructions first. In their place are installed the plastic plugs supplied. The removed bolts should not be thrown away; they will be useful when moving or rearranging during repairs.
If you have problems with the shock absorbers, you need to unscrew them and try to compress them. Since their task is to dampen vibrations, movement should be difficult. If this is easy to do, it means that both structures need to be replaced. If only one is corrected, the stiffness will be different and the load will be distributed unevenly.
If there are difficulties with the counterweights, you need to remove the machine panel (using pliers, a screwdriver, a wrench) and inspect the counterweights. If they crumble, then buy and install new ones. If it is not available for sale, you can tighten the parts with metal plates or glue them together, although this is a rather complicated option. When the counterweights look intact, it is worth examining their mountings, as well as the springs. If they break, they are replaced, but if they are intact, the bolts are tightened.
To resolve the issue with the electric motor, you need to remove the back panel and try to tighten the fasteners. Also, removing the far cover will allow you to determine the condition of the belt leading from the engine to the drum. Other actions with the motor and the programmable part of the device cannot be carried out independently.
Bearing failure can only be repaired by a service center.

Installation

Installation of a washing machine is done in various ways. New equipment requires high-quality reliable support that will not break or warp over time. Saving on a strong foundation for household appliances will result in damage not only to the floor, but also to the washing machine itself, which was purchased quite recently. The ideal situation is installation on a concrete floor. If the floor is wooden, you need to work hard to make it just as reliable, stable, and strong. Vibration during operation of the washing machine is not allowed. It will cause many problems that will require financial costs and moral strength.

This article will reveal the main points that require attention when installing a Eurosoba washing machine on a wooden floor.

Erroneous actions when installing on a wooden floor:

1. Installation on a weak wooden floor.

Such actions will lead to strong vibration of the machine during operation, it will sway and jump on a shaky floor. Such a situation will lead to rapid breakdown of the unit.

2. Place a mat under the device.

Such a picture will eliminate vibration and noise, but will not preserve household appliances. Will have to buy a new one soon.

3. An attempt to strengthen a wooden floor with corners and metal tubes.

After choosing a place to install the machine, many owners immediately start marking, make holes in the boards for the legs, drive pipes or corners into them, place a piece of chipboard on top, and mount the washing machine on top. Such a support will not last long, which will again lead to malfunctions.

Article on the topic: What can you do at home when the TV doesn’t work 100 to 1

4. Placement of a concrete slab on top of a wooden floor.

The vibration will noticeably decrease, but the floor will gradually deform.

5.Attaching the legs to the floor.

This design involves screwing the legs of the washing machine using self-tapping screws to a wooden floor. The operating mode entails strong rocking of the unit, the floor is torn out along with the machine and boards.

Such actions do not lead to anything good. High-quality operation of a washing machine on a wooden floor without harm can be achieved only by minor modifications to the base on which the installation will be made.

Anti-vibration stands

Since this problem is not new, there has long been a simple and inexpensive solution to it - anti-vibration stands. For the most part, these products are small circles made of durable polymer that absorbs vibration, thereby ensuring stability and reliable fixation of the case on a smooth surface.

These stands have an attractive appearance and will definitely not spoil the impression of good repairs and high-quality household appliances. There are different models of stands available for sale; they differ in shape and color, so it’s easy to choose the ideal solution for any interior.

The process of installing anti-vibration products is not particularly difficult; moreover, you don’t even have to turn off the device. To prevent the machine from wobbling, simply tilt its body to one side and place a stand under each of the legs. Then the same actions are performed for the other side. There is no need to re-align the case; the material of the stands itself will ensure its horizontal position.

Wood floor refinishing options

There are two ways to properly remodel a floor to accommodate a washing machine.

1. Concrete screed.

You will need to make a concrete screed under the wooden floor. This design will create a reliable foundation for the smooth operation of any washing machine. What is the manufacturing process:

We decide on the final location, mark places on the floor and wall. The markings are made with an increase in the original dimensions by 12 centimeters.
We remove the boards.
We make formwork.
It would be good to weld a mesh of reinforcement, which will allow it to last for a long time.
Pour the concrete solution and make it even.
We are waiting for it to harden.
Restoring a wooden floor.
We install a household device.

2. Concrete slab.

This method involves taking into account certain aspects that subsequently affect the operation of the washing machine.

We concrete the steel pipes under the floor so that they can be seen from the holes made in the wooden floor. Accurate vertical position is important. A concrete slab weighing at least one hundred kilograms is laid on top.
The slab is attached to the pipes as needed. The main thing is that the pipes are firmly concreted. This design is a reliable option for high-quality washing without harm to the unit.

Article on the topic: How much does it cost to repair daewoo washing machines

3.The top floor is made of wood.

This option is applicable when the floor cannot be dismantled.

Before installation, we check the floor for strength, strengthen the boards that are loose. We test the floor for durability so that vibration does not occur during washing. Otherwise, the wooden floor will break and the machine will be damaged.
We mark the dimensions of a household device.
We drill holes along the perimeter of the marking and place small sections of steel pipes. It is important that the pipes must be located at the same level.
We install the machine.

Features of installing a washing machine on a wooden floor

Any washing machine is a very powerful unit. During the spin mode with a centrifuge, it begins to create strong vibration, which can lead to deformation of the floor during prolonged use. In addition, a room with a concrete coating does not require any investment. Now we should take a closer look at how to install a washing machine on a wooden floor?

With a wooden floor, things are much more complicated. Since strong shocks can easily damage natural wood, careful consideration must be given to how to install. In addition to the floor, a precarious position on a wooden floor can also affect the performance of the unit and lead it to a deplorable state.

Reasons for the spontaneous movement of large household appliances

The main reason for a washing machine to move is vibration. The fact is that during the rotation of the drum with laundry, a centrifugal force arises, which is transmitted to the body of the device. Most of it is damped by a counterweight and a shock absorber system with springs. If the engine is turned on at maximum speed, and the laundry is distributed unevenly inside the drum, the vibrations cannot be completely suppressed.

Most often, narrow models “walk”. Manufacturers, trying to reduce the size and weight of the device, install excessively light counterweights inside. Their inertia is not enough to stabilize the drum during spinning. At the same time, in other modes the body is completely motionless.

If you notice that a recently purchased device moves on its own, the cause of the movement may be improper installation. Often it is enough to simply level the case, and the problem will go away by itself.

Of course, damage to one or more units of the washing machine cannot be ruled out. The reasons for vibration can be different, for example:

Mistakes to Avoid

Speaking about the vibration of a washing machine on a wooden floor, it should be mentioned that this is powerful destructive energy directed at a front-loaded unit. The stability of this state gradually shortens the service life of the most important parts and leads to inevitable breakdown.

Article on the topic: What do the icons on the Atlant washing machine mean?

Built-in washing machine

When the base of the washing machine rests on a hard surface and vibrations are dampened, the life of the washing machine is automatically extended without failures in the system. If the unit is placed incorrectly on a shaky floor, it “jumps” and sways from side to side.

Car on the floor

To prevent users from making mistakes in the future, you should carefully consider several examples of incorrect placement:

According to the calculations of some skilled users, a thick anti-vibration mat spread over a shaky wooden floor should save the situation. However, it turns out exactly the opposite; vibration, of course, is dampened, but again to the detriment of the equipment used. The car in this position suffers no less than usual.

If you don’t mind the time, there is another no less original way to install a washing machine on a raised wooden floor. It's quite easy to make. Four holes are cut into the wooden floor into which metal tubes are inserted. Then place thick sheets of plywood on top of the simple structure. The result is the same: the supports quickly become unusable and have to be replaced. The car continues to briskly jump around the country house.

Tray for the machine

There are also folk craftsmen who are ready to put a massive concrete slab on top of the wooden covering. The machine, of course, does not vibrate, but this does not make the floor any newer. Moreover, the effectiveness of this method is clearly in doubt, since the required area for high-quality extinguishing must be at least 2 square meters. m.
There are craftsmen who are trying to fix a washing machine on a wooden floor. This method does not bode well for the owner, since in centrifuge mode the machine vibrates and jumps with such force that it is quite capable of tearing out wooden boards. The noise is no less.

Article on the topic: Tesler refrigerators whose compressor

Having examined several common eccentricities of skilled craftsmen, we conclude that the proven methods recommended by the manufacturer, which allow for fastening, are much more reliable than the invented ones.

Location of counterweights

Finding counterweights in an automatic machine is very easy. The easiest place to get to is the top weight. However, there are always more problems with dismantling this block. To “climb” to it, you need to:

The upper counterweight will be immediately in front of your eyes. The unit must be inspected for defects. Next, you need to evaluate the condition of the front weights; to do this, you will have to remove the front wall of the case. The further algorithm of actions will be as follows:

Now you can inspect the front counterweights. If there are many cracks on them, the elements will have to be replaced. We'll show you how to remove damaged concrete weights to make room for new blocks.

Sequence of installation steps

It is quite possible to install the unit on the 2nd floor of a house on a wooden floor without disastrous consequences. The concrete screed allows you to strengthen the place so well, providing reliable support even for the most “bouncy” unit.

There is a certain sequence for performing screeding under wood covering:

Accurately calculate the location for installing the unit. Make several key marks on the horizontal and vertical surface.
Carefully open the boards.
Place formwork around the perimeter. To make things less expensive, you can use old boards or slabs.
If possible, it is necessary to secure a metal mesh of rigid rods for stability of the base and tenacity of the screed.
We prepare the solution and start pouring the floor. Then we move on to leveling and compacting it.
We add more logs around the perimeter of the platform so that the wood covering does not dangle in the air.
Now all that remains is to wait for the solution to dry. After fixing the board in its original place to the new joists. And finally, connect the washing machine, checking the reliability of the design.

Machine on laminate

The presented material is perfect for solving the problem yourself without extra costs.

Plywood podium

Such a base is easier and cheaper to make. It does not require much time, but is inferior to concrete in strength. This means that this option temporarily solves the problem of stability and requires periodic monitoring and updating of the design .

Inventory

As a set of materials you will need:

The tools you need to work with these materials are:

Making a podium

In this case, there is no need to dismantle the laminate or boards, which simplifies and speeds up the work. If necessary, you will need to strengthen the floor by eliminating unwanted movement of the boards. After this you need:

All that remains is to install the washing machine on the finished base and level it by adjusting the legs. Then you can proceed to connecting communications.

Installing a washing machine on a wooden floor: installation method

Article on the topic: Is it possible to add perfume to the washing machine?

However, even if you need to mark the device specifically on a wooden floor, this can be done with relatively little labor.

The structure must be level and solid

Installation Requirements

Before you begin installation work, you need to figure out where and how the washing machine should be placed.

As a rule, the standard instructions recommend adhering to the following requirements:

Firstly, the base for installing the device must be as level as possible. A machine placed skewed on one side will vibrate much more during the spin cycle than a properly mounted machine, which will lead to increased wear of its internal components.

The smoother the base, the more reliable the installation

Note! The vast majority of models are equipped with adjustable legs, which make it possible to adjust the vertical position of the device. However, the stroke of these legs rarely exceeds 20-30 mm, therefore preliminary leveling of the field is highly desirable.

Secondly, the wooden flooring under the base of the machine must be strong and stable. With strong vibration impacts, the fasteners are the first to suffer, so before starting installation it is advisable to strengthen the boards with additional nails or self-tapping screws.

In addition, do not forget about other wishes for the installation location:

The machine should be located in close proximity to the water supply - then it can be connected without laying additional branches, but simply using the hose included in the kit.
It is also advisable to choose a location for installation in close proximity to electrical outlets. Of course, you can use a carrier, but it is not advisable to do this in conditions of high humidity.

Article on the topic: Where is the low pressure fitting of the Prado 90 air conditioner located?

Photo of connection to the drain

Draining water is another problem that needs to be solved. The best option is to connect the drain pipe to the siphon of the sink or bathtub.
Finally, it is worth thinking about the position of the machine relative to other objects in the room. Contact of the walls of the device with the bathroom, cabinets, and even more so with a ceramic sink is undesirable, since vibration can lead to breakdown.

Installation method

If there is a possibility of reconstruction

The price of a good automatic washing machine is quite high, so it will be a shame if it breaks down in the first year of use. So you need to pay close attention to the correct installation of the device.

Part of the flooring needs to be removed

If possible, the wooden flooring at the installation site must be partially disassembled and a concrete base poured from below.

We do this according to the following scheme:

To begin, mark the contours of the machine on the floor boards.

Note! When marking, it is advisable to add at least 30-40 mm in all directions so that the legs do not stand on the edges of the concrete slab.

Then we dismantle the boards, removing them from the joists.
We install support beams along the perimeter of the future pouring, otherwise the edges of the boards obtained after trimming will hang in the air.
We install formwork from thick plywood. We line the inside of the formwork with polyethylene, which will provide, among other things, additional waterproofing.
We lay a frame of reinforcing bars inside the formwork. In principle, you can do without it, but then the foundation will not be so strong.

Article on the topic: Do you need a filter for a dishwasher?

Pouring and leveling the concrete area

Fill and compact the solution thoroughly. We level the surface so that it is flush with the floor or slightly higher.
We return the boards to their place, nailing them to the joists and support bars around the perimeter of the base for the machine.

Now we need to wait until the concrete reaches its design strength. Since under normal conditions this takes about four weeks, it is advisable to complete all work in advance.

At the end you still need to level the legs

Installation over plank flooring

In some cases, dismantling the floor boards is not possible, so you have to look for an alternative solution to the problem.

Before installing the washing machine on a wooden floor, we tap the flooring and, if necessary, strengthen all the boards. The base must be absolutely motionless, otherwise the slightest vibration will provoke its destruction within a short time.
Then we mark the dimensions of the machine on the boards.
In the corners of the marked rectangle we drill holes into which we insert sections of steel pipes. The base of the pipe must rest on the main ceiling, and the upper parts of all parts must be aligned in the same plane.

Plywood on the supports of their steel pipes

Then, from plywood with a thickness of at least 20 mm (or a chipboard sheet of similar thickness), we cut out a rectangle with our own hands, the dimensions of which are slightly larger than the dimensions of the machine.
We fix the plywood on steel supports, and cover the top with a rubber mat, which will compensate for vibration and prevent the legs of the device from slipping.

Article on the topic: How to use the candy holiday 181 washing machine

Of course, such a structure is less reliable than a monolithic concrete base. However, metal supports transfer the floor load quite effectively, and therefore the flooring will not be subject to shock and vibration.

Wood floor refinishing options

There are two ways to properly remodel a floor to accommodate a washing machine.

— Concrete screed.

You will need to make a concrete screed under the wooden floor. This design will create a reliable foundation for the smooth operation of any washing machine. What is the manufacturing process:

We decide on the final location, mark places on the floor and wall. The markings are made with an increase in the original dimensions by a dozen centimeters.
We remove the boards.
We make formwork.
It would be good to weld a mesh of reinforcement, which will allow it to last for a long time.
Pour the concrete solution and make it even.
We are waiting for it to harden.
Restoring a wooden floor.
Installs a household device.

This method involves taking into account certain aspects that subsequently affect the operation of the washing machine.

We concrete the steel pipes under the floor so that they can be seen from the holes made in the wooden floor. Accurate vertical position is important. A concrete slab weighing at least one hundred kilograms is laid on top.
Fastening the slab to the pipes is at your discretion. The main thing is that they sit deep in the ground and are concreted. This design is a reliable option for high-quality washing without harm to the unit.

Article on the topic: Is it possible to connect a Tver septic tank to a washing machine

— On top of the floor is made of wood.

This option is applicable when the floor cannot be dismantled.

Before installation, we check the floor for strength, strengthen the boards that are loose. We test the floor for durability so that vibration does not occur during washing. Otherwise, the wooden floor will break and the machine will be damaged.
We mark the dimensions of a household device.
We drill holes along the marking perimeter and place small sections of steel pipes. It is important that the pipes must be located at the same level.
We install the machine.

How to install a washing machine on a wooden floor

How to install a washing machine.

Ideally, the floor under the washing machine should be reinforced concrete. But it happens when you need to place it on a shaky wooden surface - low-quality material was used for the floor or it has a long service life. Use the level.

But it is known that it is not enough to purchase such an assistant, you need to install it properly. Drill 4 holes in the floor and insert corners or metal pipes into the floor. But in our house all the floors are wooden, and in the bathroom it’s impossible to turn around.

It does not matter what base material is used. Typically, this behavior is caused by improper loading of the washing machine or some malfunction of the automatic balancing system that protects the washing machine from excessive vibrations.

How to install. washing machine on the floor. and it won't flood the floor. How are you.
We bought a washing machine. how to install the car. on a wooden floor.
Above the floor. washing machine, and on the toilet. on How to install.

Article on the topic: How much gold is in a TV record

Just adjust it. For installation you will need a hard and flat surface. In practice, many craftsmen do the following.

But this is quite troublesome and expensive. By unscrewing the legs, you will ensure that your machine is level and stable. On a wooden floor, the machine will vibrate strongly during the spin cycle and will quickly fail. To prevent this from happening, or at least reduce the likelihood, you must follow the rules outlined in the user manual.

The washing machine is equipped with four adjustable legs, which are a screw connection with a rubber or plastic support. Another thing is that all manufacturers recommend placing machines on a solid and level base.

And this is an important point. Maybe it’s still possible to place a washing machine on a wooden floor? The best option, of course, would be to concrete the part where the machine will stand.

In any case, the washing machine must be level and stable, then the automatic balancing will work normally and the machine will not vibrate or jump. Do not use different supports to compensate for unevenness. After leveling, place the level along the other diagonal.

Buy special pads, place a sheet of chipboard or a rubber mat. This way the machine is installed on a flat surface and the level of vibration is reduced. A washing machine is a necessary attribute in every home.

An uneven floor or a shaky foundation provokes their manifestation. It must be installed on a rigid and durable, level base. By twisting the support clockwise, you reduce the height of the leg, and counterclockwise, you lengthen it. Then the noise level during operation will decrease, and the service life of the machine will increase.

Article on the topic: How to remove grease from a TV in the kitchen

The issue of installing a washing machine on a wooden floor is faced by many who live in old houses and it is not wise to redo something. Structurally, an automatic washing machine can be placed on either a wooden or any other floor.

Washing machines should be installed by specialists in this field and preferably licensed companies.

If the base is shaky, then indeed, the car can jump and move to the side.

Do not allow the washing machine to come into contact with walls or furniture.

Why does the washing machine jump during the spin cycle?

So-called washing machine jumping is a strong vibration that causes the equipment to twitch and move from its place. This phenomenon causes a lot of problems, at least it is accompanied by loud noise, which disturbs not only residents, but also their neighbors. There are several possible reasons for this behavior of the equipment.

Unsuitable installation location

The wrong location for the washing machine is one of the most common causes of jumping. Taking into account the force of vibration that occurs during spinning, the technique is often called capricious - it requires a flat and hard floor. There are two possible options:

unstable floor covering, soft floor (for example, wooden) - in this case, the very place on which the machine is installed will be mobile, which means that with strong vibration it will bounce significantly;
uneven floor. Even if there are tiles at the installation site, this does not guarantee a stable position of the equipment. Inexpensive tiles themselves may be a little crooked, and flaws during installation are possible. Thus, different floor levels under the legs of the washing machine will increase vibrations and provoke jumps.

There is only one method to solve the problem - eliminate floor defects. So, if it is soft or shaky, it is better to move the equipment to another place, and if the floor is crooked, then it will be enough to adjust the height of the legs of the machine. It's easy to do:

First you need to determine which legs are adjustable. To do this, just swing it - the leg on which the machine falls when swinging needs to be lengthened.
Use a wrench to turn the adjustable leg counterclockwise. Sometimes this can be done without lifting the car, but if this is inconvenient, then the equipment will still have to be tilted.
When the rocking goes away, you need to check whether the machine is level - for this you should use a building level.

Improper preparation for use

If jumping appears on a machine that was recently purchased, the first thing you need to check is the transportation bolts. They are fasteners that hold the drum during transportation and must be removed before starting the device - then the drum will fall into place and the vibration damping system will work at full strength. Often, temporary fastenings are simply forgotten, and then the device begins to vibrate and jump violently. In this case, it is urgent to remove the forgotten bolts - their number depends on the specific model and manufacturer; you can do this yourself, following the instructions for commissioning.

Before using the machine, be sure to remove the transport bolts

Machine breakdown

If a breakdown occurs in the vibration damping system of the washing machine, it begins to behave extremely actively and bounce strongly during the spin cycle. If the device is installed correctly, then one of the parts may have failed:

shock absorbers, which are located below on the sides of the tank and absorb vibrations through the resistance of the piston;
springs on which the tank is attached to the top (they stretch over time);
counterweight (a large weighting material that is located on top of the tank and ensures the stability of the washing machine; over time, it can crumble or become loose on the fasteners).

There is only one solution to this problem - call a competent washing machine repairman, who will carry out diagnostics and make the necessary replacement of parts.

Incorrect download

Strong vibration and jumping with a characteristic roar of the drum often occur due to non-compliance with the operating rules of the washing machine. Things in the drum, huddled together in one big lump, simply do not allow it to rotate evenly, creating vibrations that are dangerous for the safety of the equipment. To avoid this problem, you need to take into account a number of rules:

do not exceed the weight of loaded items specified in the instructions for a specific model of washing machine;
things need to be laid out when loading into the drum; they cannot be thrown in one lump;
The problem often occurs when washing one large item - in this case, you need to stop the cycle and redistribute the item in the drum.

Strong vibration and, as a result, jumping during operation of the washing machine is a common problem that can be caused by both improper operation and serious breakdowns. If eliminating simple violations does not produce results, then you should contact a specialist.

Installation location

If the machine will be installed in the kitchen or in a room (not in the bathroom), then there must be a reinforced concrete floor under it. It is not recommended to install the washing machine on a wooden floor, linoleum or laminate - the machine will constantly vibrate both during washing and during spinning.

In any case, you have reinforced concrete floor slabs under the wooden flooring, so you need to remove the wooden floor and fill the area under the machine with concrete mortar to the level of the old floor.

Subsequently, you can adjust the tightness of the legs of the machine to all four points on the floor - for this, the legs are equipped with threads.

If the floor under the machine is perfectly level (check with a level), then screw the legs in all the way - the shorter the height of the legs, the less conditions for vibration.

If the machine is installed in the bathroom, then the floor there is already concrete, and you don’t need to do anything. The only obstacle is the tiles on the floor. The machine can slide on it when working, so you just need to place a rubber mat under it.

Article on the topic: How to remove the control unit of an Ariston washing machine

If this is not done, then after a while you will see that the tiles under the machine will begin to crack and break into small pieces.

Is it possible to fix the washing machine to the floor?

During the spin cycle, the Samsung SM moves quite a lot. Has anyone attached the SM to the floor? What was the result? What's the best way to do this?

You can make four holes on the tile for the legs, if it’s in the bathroom. Maybe there’s just an imbalance in the linen?

Is the machine level?

2ndreika I am interested in principle: will the SM break if it is rigidly attached to the floor?

2Alex_Kov You wrote a very valuable comment

2mixator No. Just standing on the floor.

coyot78 wrote: won't the SM break if it is rigidly attached to the floor?

It seems to me that with a policy of complete trust in the existing modern drum balancing system (with its clearly observable efficiency) and rigid fastening of the SM body to the floor, its innards will be smashed into rubbish in less than a year.

Shikhael Muma wrote: it seems to me that with a policy of complete trust in the existing modern drum balancing system (with its clearly observable efficiency) and rigid fastening of the SM body to the floor, its innards will be smashed into rubbish in less than a year.

and if she jumps with all her guts, then there is a chance of breaking them in the same period of time.

coyot78 wrote: During the spin cycle, the Samsung SM moves quite a lot. Has anyone attached the SM to the floor? What was the result? What's the best way to do this?

did you remove the shipping bolts? I found some information here,” > “In general, rigid fastening of the machine’s legs to the floor is not provided. But in a number of cases (for example, when installed on a plinth, on an inclined slippery floor, on an unstable wooden floor, etc.), such fastening can be done. For this purpose, some models have special brackets for attaching the front legs.”

A short digression about what will happen if the transport bolts are not removed. We once received an application for warranty repair of an ARDO A-600X washing machine located in a rural area. When asked what was wrong with the machine, the owner answered briefly: it doesn’t work.

When the master arrived at the place, the following picture appeared before his eyes. The machine worked for 8 (.) months with the transport fastenings not removed. To prevent the machine from jumping around the room, the owner replaced the front rubber support legs with a stationary mount made of a metal corner, fixed with dowels to the floor.

In addition, the machine is almost completely covered with brickwork on both sides. After the owner dismantled his structures and removed the machine and opened it, the following was discovered:

Source

Installing a washing machine on a wooden floor: doing it right

Such a problem as installing a washing machine on a wooden floor is especially pressing for those who live in an old house or in a country cottage. But, as you know, there are no unsolvable problems.

The happy owners of a brand new home helper should think about how best to arrange for her so that she can perform her duties for many years without causing the owners much trouble or minor troubles.

One of the “inconveniences” can be periodic vibration and even unpredictable “jumps” of the washing machine during operation.

To prevent this from happening, it is necessary to prepare in advance a permanent place for installing the purchased unit.

Each modern model is necessarily equipped with a system that provides automatic balancing.

But manufacturers still advise placing the washing machine on a solid concrete base to avoid shifting.

If this is unattainable for you, this is not yet a reason for frustration and refusal of the desired purchase. And on a wooden floor you can perfectly organize a permanent location for your new clothes.

New wood floors are particularly durable, and there will be no issues with installing a washing machine. All you have to do is adjust the horizontal level, tighten the legs a little if necessary, connect to the communications and you can safely start using it.

Related article: How to disassemble a whirlpool top-loading washing machine

It’s another matter if the floors in the house are quite old and “living”. You'll have to do a little work here. Depending on the situation, you can choose one of the ways to fix the problem:

concrete the part of the floor on which the machine will stand (provided, of course, that you will never move it to another place in the future).
A less expensive option is to build a small, stable “podium” on which to install a washing machine.

Anti-vibration mats

Another product that is designed to prevent the washing machine from spontaneously moving on the tiles is anti-vibration mats. A thin and aesthetically pleasing product will make the body stand in place, significantly reduce vibration during spinning, and therefore help reduce the level of noise produced.

Externally, the product looks like an ordinary rubber mat, but structurally it consists of two layers with different characteristics. The top layer provides anti-slip action, the bottom has anti-vibration properties. The product has a porous structure. The materials used in its manufacture ensure resistance to deformation under load. The mat is resistant to moisture and household chemicals and can be used in a wide temperature range.

All that needs to be done to prevent the car from jumping on the tile is to lay this product on the floor so that each of the legs stands on it.

Proflex products are distinguished by their high quality and environmental safety. Anti-vibration mats are two-layer, odorless, and in addition to reducing noise levels, they act as an antistatic agent, preventing charge from accumulating on the body.

Mattix-Vibromats sheets and stands are characterized by high wear resistance. Can be used even at extremely low temperatures. This is a good choice for a warm apartment and cottage that does not have heating.

Lux products are budget-level anti-vibration mats and stands. At a relatively low price, the products have fairly good consumer characteristics.

Shahintex mats are universal; they are perfect for both a narrow, small-sized washing machine and a full-fledged laundry combine. The products do their job perfectly, absorb vibration, reduce noise, do not require special care, and are easy to clean.

Vibration and spontaneous movement of the washing machine is really a problem that anyone can face. A seemingly minor nuisance can result in a serious accident or breakdown, which will entail costly repairs.

With all this, it is easy to avoid catastrophic consequences; it is enough to initially use anti-vibration stands or other products for a similar purpose and, of course, correctly install and connect the machine.

Source