Rating of the best self-priming pumps: what nuances to pay attention to when choosing

Best Conventional Surface Pumps

Conventional surface pumps are installed outside the source, connecting the device to it using a conventional hose. In case of year-round use of the pump, it is necessary to provide protection for the housing from low temperatures, since water frozen inside the working cavity can lead to breakdown. Typically, the power of a household surface pump is designed to pump water from a depth of up to 10 meters. The advantages of such devices are simple installation, primitive design and high mobility.

The best sewer installations

3. UNIPUMP Sanivort 605 M

It is special equipment, the main purpose of which is to remove wastewater from the sink, toilet, shower and other equipment if they are located at a lower level compared to the sewer system. In addition, such a pump will be very suitable for areas where there is no possibility or reason to organize sewer drainage by gravity. The body of the product is made of high-quality plastic and is easy to clean if necessary. Inside the device there is a pump with a grinder, which does an excellent job of passing fecal matter, toilet paper, food debris, and so on.

More: Top 10 best vacuum cleaners for cleaning animal hair

The design provides three inputs: one of them has a diameter of 100 mm and is intended for connecting to the toilet, two more, 40 mm each, for connecting a sink, shower, and so on. All the mass passed through the chopper will be forcibly discharged through the outlet, the diameter of which can be 23, 28 or 32 mm. At the outlet of the station there is a check valve that prevents wastewater from returning back to the pump. The device’s engine is equipped with a reliable thermal protection system that will turn it off if the temperature rises above critical. This can happen due to jamming of the blades, the passage of too hot water, and so on. The model is intended for toilets equipped with a horizontal outlet with a flush tank volume of 6 liters or more.

Advantages:

• Very easy to install and operate;
• Works absolutely silently;
• Collects wastewater from three points at once;
• Good value for money product;
• Equipped with a non-return valve.

Flaws:

• The float mechanism requires regular maintenance.

UNIPUMP Sanivort 605 M

2. Grundfos Sololift 2 C-3

This is an automatic sewer type pumping unit, characterized by small overall dimensions. It can be used in absolutely any building, but most often such a device is purchased for themselves by the owners of private houses or cottages. The product is used for pumping gray water that does not contain feces. Developed on the basis of modern European standards. The manufacturer has installed a fairly powerful and durable engine here, which is reliable at water temperatures up to 90 degrees. The inlet and outlet connections can be adjusted in height, which greatly ensures ease of installation, operation and replacement. The design provides two levels of activation at once - the user has to choose the optimal one.

The overall dimensions are small, so such a pump can be installed even in fairly narrow places. The unit, which contains the motor and pump, is not only compact, but also removable, so maintenance of the equipment does not take too much time. In addition, you do not have to disconnect the outlet or inlet line to do this. This pump works best with washing machines, dishwashers, and showers. The motor has a special thermal switch with a restart, which is activated when the engine temperature drops to the required parameters. A long period of operation is guaranteed largely due to the presence of three sealing shafts and an additional chevron cuff. It uses a vortex pump through which particles with a diameter of up to 2 cm can pass.

Advantages:

• Very easy to maintain - no need to completely disassemble during cleaning;
• Pumps fairly large volumes well;
• Occupies a minimum of free space in the room;
• Not very noisy.

Flaws:

• There is no way to connect to the toilet.

Grundfos Sololift 2 C-3

SFA SANIVITE Silence

This model went on sale just a few months ago, but has already gained popularity among ordinary users due to its high quality workmanship and reasonable price. This sewer pump can be connected to a sink, washing machine or dishwasher, shower stall, bidet and other plumbing equipment with the exception of the toilet. The design is made of high-quality materials, has an attractive appearance and high performance. It operates almost silently and can be used safely. The case has excellent acoustic insulation, due to which the transmission of sounds is much weaker, which allows it to be installed even in the kitchen itself.

The pump is manufactured using the most modern technologies and fully complies with Russian, European and international standards. The system operates as efficiently as possible throughout its entire service life. The power of the product is 400 W, per hour it is capable of pumping up to 6 cubic meters - quite enough even for a large family. The model is capable of working even with heavily contaminated water, the maximum temperature of which can reach 60 degrees. The design is equipped with a check valve, so no unpleasant odors will enter the room.

Advantages:

• Good operational reliability;
• It operates almost silently;
• Long period of operation;
• Does not require special maintenance;
• The presence of a check valve protects against unpleasant odors;
• Small overall dimensions.

Flaws:

• No exceptions were found for the relatively high price.

SFA SANIVITE Silence

The best circulation pumps for heating

Heating circulation pumps are used to force water circulation in a circle. The devices can also work with hot water, since their main area of ​​application is heating systems. The devices create pressure differences that help the fluid overcome the resistance created in the pipe. When choosing a circulation pump, you should pay attention to the pressure created, which determines how large systems the device can serve, productivity and the maximum water temperature with which the device can operate.

The leader in terms of sales of surface circulation pumps is . Grundfos

is a Danish concern, the most popular and reputable company for the production of pumping units. The production volume is more than 16 million products per year. The company's head office is located in Denmark, and its main production facilities are located in Germany. Therefore, Grundfos pumps are often called German, as evidenced by the high build quality. In 2005, a plant for the production of Grundfos pumps was opened in Russia (Moscow region).

Which company should you choose?

In order for a surface pump to operate without failures for many years, you should give preference to devices from brands that specialize in the production of pumping equipment.

Such companies pay maximum attention to quality and introduce modern technologies that allow the use of surface pumps in different climatic conditions.

The best manufacturers of surface pumps are Grundfos, Metabo, Wilo, Denzel, SFA and ZUBR.

Models from these exact brands are included in the selection.

Pumps for irrigation from a barrel

Such models are suitable for pumping liquid from containers with a depth of no more than 1.8 m. They are fixed on the side of the tank and connected to the network. These units are compact, light in weight and operate quietly. The advantage of these pumps is the ability to dilute the necessary fertilizers and chemicals in a barrel before watering. The editors of Vyborexperta.Ru chose 1 winner from 5 nominees based on the best performance and reliability.

Gardena 2000/2 Li-18

The Gardena 2000/2 Li-18 cordless submersible model is powered by an 18 V (2.6 Ah) lithium-ion battery with an LED display that shows the charge. There is also a control panel with a power button and 3-level power adjustment: 1100, 1700 or 2000 l/h. Depending on the selected mode, the operating time will be 15, 30 or 60 minutes at a maximum pressure of 2, 1.3 or 0.4 bar. The maximum suction depth is 1.8 m, the minimum is 5 cm.

The design of the watering device provides the ability to connect hoses measuring 19 and 33 mm. It can be used to pump out contents from a swimming pool, submerged boat and other medium-sized containers with a maximum head of 20 m. It also supplies liquid to the shower. The highest temperature is maintained at 35°C. The device weighs little (2.5 kg) and is equipped with an adjustable curved handle. The advantage of the model is the built-in filtration system.

Advantages:

• Availability of protection against blocking of the nose impeller;
• Versatility;
• Dry running protection function;
• Unpretentiousness in maintenance;
• Charging time – 4 hours.

Flaws:

• No hoses included.

The battery that comes with the barrel pump is suitable for all Gardena equipment that supports the HeartBeat system.

The best centrifugal pumps

The best pumping stations

VORTEX ASV-1200/24N

It is a domestically produced model that can be used to supply drinking or industrial water to a summer cottage or in a private house. The design is equipped with a very voluminous hydraulic tank, the capacity of which is 24 liters. This prevents the pump from constantly turning on and off. The case is made of high quality stainless steel. The maximum pressure is 40 meters, productivity reaches 70 liters per minute. The design is very stable, largely thanks to the special legs. A pressure gauge is provided, through which you can regulate the pressure in the water supply system.

More: Hyundai DT 405 - full review of the compact dishwasher

There is a pressure switch, the station has a power of 1.2 kW and is capable of lifting water from a depth of up to 9 meters. The latest developments in electronics are used to control the equipment, which allows optimizing the functioning of the pump and reducing the amount of electricity consumed. Users in their reviews note that the device is unpretentious and does not require special maintenance, which makes it possible to significantly extend the service life of the structure.

Advantages:

• Very reliable engine with a carefully thought-out overheating protection system;
• Volumetric expansion tank, which significantly extends the service life of the equipment;
• Excellent pump build quality.

Flaws:

• Finding spare parts is not as easy as it might seem at first glance, even though the products are domestically produced.

VORTEX ASV-1200/24N

DENZEL PSD800C

Equipped with an electric centrifugal pump, which is additionally equipped with an external ejector. The station is designed for pumping water that does not contain large abrasive particles and various types of long-fiber inclusions. This model is ideal for domestic water supply of private houses, cottages and so on. It is capable of lifting water from a depth of up to 20 meters. This product can be used as part of automatic pumping stations. The design has a mechanical type pressure switch, which will operate, including the pump, as water is consumed by consumers. The volume of the hydraulic accumulator is 24 liters.

The body of the device is made of cast iron, the impeller is made of brass. The drive is electric, asynchronous, and has an external ventilation system. On its surface there is a plastic terminal box in which you can find a capacitor and terminals for connecting the motor to the power cable. The ejector is designed to create additional vacuum in the supply pipeline - this allows water to be lifted from a sufficiently large depth. Inside the hydraulic accumulator there is a membrane made of food-grade rubber; the design also includes a pneumatic valve that allows air to be pumped into it.

Advantages:

• Excellent build quality;
• Reasonable cost;
• Unpretentiousness in maintenance;
• Long period of operation;
• Can take water from quite a great depth;
• Long warranty period – 2 years;
• With not too high power it can provide a good set;
• It works stably, the engine has reliable protection against overheating.

Flaws:

• It is strictly forbidden to use water for pumping if it contains mechanical inclusions.

DENZEL PSD800C

1. GILEX Jumbo 50/28 Ch-14

Another domestically produced model, and, according to user reviews, this design is the best surface pump designed for creating an autonomous water supply system. The volume of the expansion tank is 18 liters - quite enough for domestic needs. It is quite enough so that the pump does not turn on after two or three liters of water have been consumed from the system. If necessary, the operation of the device can be adjusted by creating higher pressure in the pipes or, conversely, lowering it. Capable of lifting water from a depth of more than 6 meters. Even if the suction pipe is located at the bottom of a well or borehole, no sand or other abrasive particles will be drawn in, since the power of the device is only 500 W, although experienced users recommend installing a coarse filter at the inlet to protect the motor blades from mechanical damage.

According to the manufacturer, this model is able to function normally even when using dirty water or water containing a large amount of dissolved gases or salts. Thorough protection against leaks is provided by seals made of graphite-ceramic materials. Experienced plumbers specifically note the short-circuited system on which the electric motor operates. This allows you not only to save on electricity, but also to extend the service life of the equipment.

Advantages:

• It starts smoothly and there are no water hammers in the water supply system;
• Reasonable cost;
• There is also reliable idle protection;
• The unit has high-quality protection against voltage surges;
• Low energy consumption.

Flaws:

• Not detected.

GILEX Jumbo 50/28 Ch-14

Inexpensive models (up to 4000 rub.)

JEMIX W15GR-10 A

• Increases pressure well
• Not noisy
• Able to withstand some dry running time
• Suitable for hot water
• Cheapness
• Low power consumption

• Not very strong body

Economical pump capable of increasing water pressure. Suitable for intensive use and pumping hot water with temperatures up to 110°C. Has a “wet” rotor type. The design is quite durable. Except for the fragile body. Can be installed horizontally or vertically. The installation method does not affect operating efficiency.

Vodotok X15G-10A

• Low price
• High quality travel sensor
• Versatility
• Not bad power

• Not suitable for hot water

Pump for increasing water pressure in a private house with a power of 90 W. It does not produce very large characteristics, but it is perfect for specific tasks. Capacity 1.2 cubic meters m/hour is sufficient for organizing a shower or other needs. In this case, the maximum pressure will be 10 m. The device is used for cold water supply with temperatures up to 40°C. If you use hotter water, problems will inevitably occur.

Aquario AC 254-130

• Robust housing
• Energy efficiency
• Economical
• Built-in overheat protection

• Low power

Flow device with three control speeds, which will allow you to change the pressure and throughput of the pump. Capable of operating at ambient temperatures from 1°C to 40°C. In this case, the maximum liquid temperature can reach 110°C. Has an inlet diameter of 1″, so adapters may be needed when connecting some components.

Features of Vilo TOP-S pumps

Such models are designed for rooms with an area of ​​up to 1400 m2. Using these devices, you can ensure accelerated coolant circulation

in all heating systems. Specifications:

Pros and cons of Vilo

There are practically no negative reviews of Vilo circulation pumps, but there is a very high risk of buying a fake

, it is almost impossible to distinguish it from the real one. The equipment is in demand due to the following advantages:

1. These devices are durable.
2. There are several levels of protection.
3. It is possible to manually switch engine speed.

Pump selection criteria

When choosing any technical device, special attention is paid to technical characteristics. A photograph of a device can only provide visual information and attract attention, but a person will receive most of the information from the description of the device. The first thing you need to do is understand what purposes it is intended for. Only after this, the optimal model is selected based on:

• The maximum depth with which the device is capable of working. It is necessary to take this parameter into account, since not all models are able to function even at a small value. It is also important to understand that the distance is measured from the body to the lower value of the source.
• To find out how efficient a pump is, you need to look at its efficiency; the higher it is, the better.
• Takes performance into account. This way a person will be able to understand whether the liters are enough for him for a day or whether it is better to buy another model.
• Pressure power. The value is measured in meters of water column. It is important to remember that high pressure is effective for home use, while low pressure is perfect for caring for a garden plot.
• Energy efficiency will help you understand how much electricity a pump will consume to pump a specific volume of water. Taking this parameter into account, a person will be able to save money when operating the unit.

Rating of pumps for increasing water pressure

A review of automatic pumps for increasing water pressure includes two types of devices: surface devices and stations. Both types are equipped with motors and require a constant supply of energy. The rating includes the best household pumps based on reviews from consumers and experts. The selection was made based on the following criteria:

• Bandwidth;
• Maximum pressure;
• Price;
• Motor power;
• Product material;
• Build quality;
• Ease of maintenance;
• Availability of additional sensors and functions.

The quietest

GILEX Compass 25/80

• Unusual appearance
• Sturdy body
• Low price
• High quality build
• Silence

• No dry running protection

Circulation pump for a modern heating or water supply system. Can also be used for conditioning. The device efficiently recirculates hot water in the coolant. With a rated power of 135 W, it provides a head of 8 m and a flow capacity of 12 cubic meters. m/hour. The installation is universal, can be either horizontal or vertical. There is overheating protection and 3 operating speeds.

ELITECH NP 1216/9E

• No noise during operation
• Cheapness
• Light weight
• Good power
• Versatility

• Not very high throughput

High-quality model with a power of 105 W for water temperatures up to 95°C. Rotor pump mechanism. The throughput is low: only 1.38 cubic meters. m/hour. So this device may not be suitable for some needs. The model weighs 2.65 kg and is equipped with a high-quality power cable 1.3 m long.

Grundfos UPA 15-90

• Relatively low price
• Silent operation
• Easy installation using couplings and nuts included
• Excellent automation
• Compactness

• The flow switch needs to be cleaned

The rating of pumps for increasing water pressure in an apartment is closed by a popular device that is well suited for use in apartments with a gas water heater. If the water pressure is low, then this pump will help correct the situation. There is automatic control: the pump turns on when the tap is opened. Can be placed in any position (horizontal or vertical). The model can withstand water temperatures of 95°C. Additionally, there is overheating protection.

You need to choose the best booster pump for water based on the specific characteristics of the water supply system. If everything is very bad with the pressure, then a device with increased power will come in handy. For non-critical problems, it is more logical to choose models of the primary and middle classes.

Which irrigation pump is better?

Surface pumps operate with clean water. They are easy to use, reliable and unpretentious. Barrel irrigation devices allow you to use water with added chemicals and fertilizers. Drainage devices are distinguished by their ability to pass contaminated liquid. The advantage of pumps for irrigation from a well is their high pressure and immersion depth.

Which pump to choose for watering a garden or organizing water supply largely depends on its purpose and capacity:

• For water supply to the house and irrigation of beds, it is better to purchase “ESPA Aspri 25 5M” with a high throughput of 7.2 cubic meters. m/h.
• If units with lower productivity are required for watering areas, then you should buy “Whirlwind PN-370” (2.76 cubic m/h) or “Quattro Elementi Giardino 401 Ci” (2.1 cubic m/h).
• The Gardena 2000/2 Li-18 (2000 l/h) powered by a battery will do an excellent job of supplying water from a barrel.
• If increased productivity is required to work with contaminated water, pay attention to the “Bison NPG-M1-400” (7.5 cubic m/h) and “Dzhileks Drainazhnik 110/8” (6.6 cubic m/h).
• If you want to buy a device for suctioning dirty water with a lower throughput, you should purchase the “Karcher BP 1 Barrel Set” (3.8 cubic m/h).
• For collecting water from a well, “Livgidromash Malysh-M BV 0.12-40 10m” with an average productivity of 1.5 sq.m. is suitable. m/h.
• If the task is to water a large area from a well, then the best option would be “Grundfos SBA 3-35 A” (3.0 cubic hours).
• For shallow wells, Technopribor Rucheek-1 is suitable.

The rating contains the highest quality models, characterized by versatility, safety and high performance.

Grundfos UPS 25-40 180

​Photo: https://beru.ru

A very good surface circulation pump that can be a good choice for many buyers. Its weight is only 2.5 kg, making transportation and installation much easier. Suitable for pipes with a diameter of one and a half inches, which are used quite often in heating systems. The throughput is very good - as much as 4 cubic meters per hour. The maximum pressure is not too high - only 4 meters. However, this will not cause problems - a larger figure is basically not needed, unless we are talking about a two- or three-story mansion with high ceilings. The pump is suitable for clean water of both low and high temperatures - in the range from +2 to +110 degrees Celsius.

Circulation pump UPS 25-40 180 (45 W)

Advantages:

• light weight
• long service life
• low noise level
• efficiency
• good performance
• small dimensions

Flaws:

• not detected

How to choose a pump for irrigation

When choosing, you need to pay attention to the type of device, the quality of the required water, the maximum pressure, throughput and immersion depth.

Type

Which pump is best for irrigation depends on its type. Surface devices work with relatively clean water and are mounted on the surface. They are suitable for those who want to provide water supply to the house and irrigation of the site. For watering from a barrel and a well, it is better to choose highly specialized models. The first ones have a low immersion depth, light weight and are equipped with a filter. The latter are suitable for working with clean water and have a greater immersion depth. Drainage models are great for pumping out contaminated liquid.

Water quality

Pumps operating with contaminated water are equipped with a filter or grinder. Therefore, they are suitable for pumping out of swamps, cesspools, dirty pools, ponds and containers containing impurities in the form of sand, branches, leaves, silt and other debris. If the object to be collected is not contaminated, then you can safely buy a model that works only with clean water.

Maximum head

If you need to irrigate an area of ​​up to 300 m, then models with a maximum pressure of up to 30 m are suitable. For areas ranging from 300 to 1000 m, it is better to choose devices with a rating of 30-100 m.

Bandwidth

For a specific case, it is necessary to carry out a calculation by multiplying the area by the desired volume of water. To irrigate beds in hot weather, experts recommend using about 5 liters per 1 square meter. m. Based on this, to water a garden with an area of ​​600 square meters. m. an engine power of 1.0-1.5 kW will be sufficient, providing a throughput capacity of 2500-3000 l/hour.

Immersion depth

If you purchase a pump for pumping water from shallow sources (shallow well, large barrel), models with a immersion rating of up to 9 m are suitable. Usually, preference is given to surface devices. For supply from wells, ponds and other deep sources, you should pay attention to devices that support a depth of more than 10-20 m. Submersible devices meet these criteria.

The best lawns

Grundfos UPS 25-60 180

​Photo: https://beru.ru

Are you looking for an inexpensive surface pump for good watering of your dacha or suburban area? Surely this one will suit you. After all, this model can lift water to a height of up to six meters! And its productivity is very good - 4.35 cubic meters per hour. Works great with liquid in a wide temperature range - +2...+110 degrees. The “wet” rotor provides not only good performance, but also a higher level of reliability due to the simplest possible design. It’s nice that this circulation pump has a very small weight - only 2.6 kg.

Circulation pump UPS 25-60 180 230V (60 W)

Advantages:

• works almost silently
• affordable price
• practical and reliable
• compactness
• significantly maximum pressure

Flaws:

• some models vibrate strongly during operation